Sony STR-ZA1000ES User Manual Download

Page: 156 / 187

PROTECTOR

The receiver will automatically turn off after a few seconds. Check the following:

There may be an electrical surge or power failure. Unplug the AC power cord (mains

lead) and then plug in the cord again after 30 minutes.

The receiver is covered and the ventilation holes are blocked. Remove the object

covering the ventilation holes of the receiver.

The impedance of the connected speakers is below the rated impedance range indicated

on the back panel of the receiver. Reduce the volume level.

Unplug the AC power cord (mains lead) and let the receiver cool down for 30 minutes

while performing the following troubleshooting:

Disconnect all of the speakers and subwoofer.

Check that the speaker wires are tightly twisted on both ends.

Connect the front speaker first, increase the volume level and operate the receiver for at least 30

minutes until it completely warms up. Then, connect each additional speaker one by one and test

each additional speaker until you detect which speaker is causing the protection error.

After checking the above items and fixing any problems, plug in the AC power cord

(mains lead) and turn on the receiver. If the problem persists, consult your nearest Sony

dealer.

[133] Troubleshooting

Error messages

UPDATE FAILED

Insert a USB flash drive on which the package file for updating the receiver is saved, and

then turn the receiver off and turn it on again.

[134] Troubleshooting

Error messages

FAN STOPPED (for STR-ZA3000ES)

Check that the ventilation holes on the top of the receiver are not blocked.

[135] Troubleshooting

Error messages

List of messages after Auto Calibration measurements

Summary of Contents for STR-ZA1000ES




























































































































































































Search results

Summary of Contents for STR-ZA1000ES

Reviews:

Related manuals for STR-ZA1000ES

Brands by name

Popular brands

Sony STR-ZA1000ES, User Manual

Search results

Summary of Contents for STR-ZA1000ES

Reviews:

Related manuals for STR-ZA1000ES

Brands by name

Popular brands