background image

STR-V5550/V7770

E Model

Chinese Model

SERVICE MANUAL

FM STEREO/FM-AM RECEIVER

MICROFILM

SPECIFICATIONS

This set is the tuner and amplifier
section in MHC-V5550/V7770AV.

Amplifier section

The following measured at AC 230V 50/60 Hz
DIN power output (Rated) (FRONT)

95 + 95W (6 

 at 1kHz DIN)

Continuous RMS power output (Reference)

FRONT SPEAKER: 110 + 110W
(6 

 at 1kHz, 10% THD)

CENTER SPEAKER: 55W
(8 

 at 1kHz, 10% THD) (V7770)

REAR SPEAKER: 35 + 35W
(8 

 at 1kHz, 10% THD) (V7770)

The following measured at AC 120, 220, 240V 50/60Hz
DIN power output (Rated) (FRONT)

100 + 100W (6 

 at 1kHz DIN)

Continuous RMS power output (Reference)

FRONT SPEAKER: 120 + 120 W
(6 

 at 1kHz, 10% THD)

CENTER SPEAKER: 60W
(8 

 at 1kHz, 10% THD) (V7770)

REAR SPEAKER: 40 + 40W
(8 

 at 1kHz 10% THD) (V7770)

Peak music power output 2400W (V7770)

2000W (V5550)

Inputs

MD/VIDEO 1 IN (phone jacks): voltage
450/250mV, impedance 47k

AV INPUT AUDIO (phone jacks): voltage
250mV, impedance 47k

MIX MIC 1/2 (phone jack): sensitivity 1mV,
impedance 10k

Output

MD/VIDEO 1 OUT (phono jacks): voltage
450/250mV, impedance 1k

PHONES (stereo phone jack): accepts
headphones of 8

 or more.

FRONT SPEAKER:
accepts impedance of 6 to 16

CENTER SPEAKER:
accepts impedance of 8 to 16

 (V7770)

REAR SPEAKER:
accepts impedance of 8 to 16

SUPER WOOFER:
Voltage 1V, impedance 1k

Photo : STR-V7770

Tuner section

FM stereo, FM/AM superheterodyne tuner

FM tuner section

Tuning range

87.5 – 108.0MHz

Aerial

FM lead aerial

Aerial terminals

75

 unbalanced

Intermediate frequency

10.7MHz

AM tuner section

Tuning range
Thai models:

531 – 1,602kHz (with the AM tuning
interval set at 9kHz)
530 – 1,710kHz (with the AM tuning
interval set at 10kHz)

Other models:

MW: 531 – 1,602kHz (with the MW tuning
interval set at 9kHz)
530 – 1,710kHz (with the MW tuning
interval set at 10kHz)
SW: 5.95 – 17.90MHz (with the SW tuning
interval set at 5kHz)

Intermediate frequency

450kHz

Antenna

AM loop antenna External antenna terminal

General

Power requirements
Chinese, Thai models:

220V AC, 50/60Hz

Other models:

120V or 220V or 230 – 240, 50/60Hz
Adjustable with voltage selector

Power consumption

300W

Dimensions (w/h/d)

Approx. 288 

×

 205 

×

 375mm

Mass

Approx. 8.8kg

Design and specifications are subject to change without notice.

Summary of Contents for STR-V5550





















































Reviews: