English
Before operating the unit, please read this manual thoroughly and retain it for future
reference.
WARNING
To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquid, such as vases, shall be placed on the apparatus.
WARNING
This installation should be made by a qualified service person and should
conform to all local codes.
ATTENTION
The electromagnetic fields at the specific frequencies may influence the picture of
this unit.
IMPORTANT
The nameplate is located on the top.
Features
The SSC-YB411R/YB401R color video camera is equipped with the 1/3 type
Super
HAD CCD II™*
.
The SSC-YB511R/YB501R color video camera is equipped with the 1/3 type
EXview HAD CCD II™**
.
It has the following features:
The focal length
ˎ
ˎ
of the lens is 3.1 mm (SSC-YB501R/YB401R) and 6.0 mm
(SSC-YB511R/YB411R).
High resolution and high sensitivity
ˎ
ˎ
Day/Night function allowing color/monochrome mode switching
ˎ
ˎ
Noise Reduction
ˎ
ˎ
Automatic white balance tracking and adjustment (ATW).
ˎ
ˎ
DC 12 V power supply system.
ˎ
ˎ
* Super HAD CCD II™
is a trademark of Sony Corporation. (SSC-YB411R/YB401R)
** EXview HAD CCD II™
is a trademark of Sony Corporation. (SSC-YB511R/
YB501R)
Notes on Use
Power supply
The SSC-YB511R/YB501R/YB411R/YB401R operates on DC 12 V power.
– When connecting the transformer, be sure to connect each lead to the appropriate
terminal. Wrong connection may cause malfunction and/or damage to the video
camera.
Handling of the unit
Be careful not to spill water or other liquids on the unit, or allow combustible or
metallic objects to fall inside the body. If used with a foreign object inside, the
camera is liable to fail, or be a cause of fire or electric shock.
Operating or storage location
Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,
avoid operating or storing the camera in the following locations, as these can be
a cause of a malfunction.
Extremely hot or cold places (Operating temperature: –10°C to +50°C)
ˎ
ˎ
Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,
ˎ
ˎ
near heaters)
Close to sources of strong magnetism
ˎ
ˎ
Close to sources of powerful electromagnetic radiation, such as radios or TV
ˎ
ˎ
transmitters
Locations subject to vibration or shock
ˎ
ˎ
Humid or dusty locations
ˎ
ˎ
Locations exposed to rain
ˎ
ˎ
Locations under the influence of fluorescent light or reflection of a window
ˎ
ˎ
Under an unsteady light (the image will flicker.)
ˎ
ˎ
Where it is subject to moisture.
ˎ
ˎ
Where it is subject to fume and swear.
ˎ
ˎ
This camera is not for Outdoor use, and don't use the camera with housing in
ˎ
ˎ
any installation environment.
Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
When transporting the camera, repack it as originally packed at the factory or in
materials of equal quality.
Cleaning
Use a blower to remove dust from the lens.
ˎ
ˎ
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn
ˎ
ˎ
stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may
ˎ
ˎ
damage the surface finishes.
In the event of any problems with the operation of the camera, contact your Sony
dealer.
Note on laser beams
Laser beams may damage the CCDs. If you shoot a scene that includes a laser
beam, be careful not to let a laser beam become directed into the lens of the
camera.
Note
On the characteristics of Electrical D/N, the color reproduction of the picture
could be partially failure in the case camera works under the environment of IR
light source or high IR reflectance situation. (SSC-YB411R/YB401R)
Phenomena Specific to CCD Image Sensors
The following phenomena that may appear in images are specific to CCD
(Charge Coupled Device) image sensors. They do not indicate malfunctions.
White flecks
Although the CCD image sensors are produced with high-precision technologies,
fine white flecks may be generated on the screen in rare cases, caused by cosmic
rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
- when operating at a high environmental temperature
- when you have raised the gain (sensitivity)
- when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or flashlight, is being
shot, vertical tails may be produced on the screen, or the image may be
distorted.
Monitor screen
Vertical tails shown on the image
Bright object (e.g., strong spotlight, strong
reflected light, flashlight, the sun)
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
Location and Function of Part
Top/Front/Right Side
Lens
Front cover
Tripod screws
The screw holes for attaching the tripod are located on
both the top and bottom of the camera. Use a 1/4" 20
UNC screw to attach a tripod to the camera.
The tripod must be set up on a flat surface and tightened firmly by hand.
Caution
Use the mounting screw whose length is 4.5 mm – 7 mm only. Use of other
screws may cause improper mounting and damage parts inside the camera.
Rear
VIDEO OUT (composite video signal output) connector (BNC type)
Fall-prevention rope mounting hole
When installing the camera on a ceiling or wall, be sure to secure a fall-
prevention rope (not supplied) to this hole for safety.
DC 12 V (power input) terminal (DC 12 V ±10%)
Installing the front cover
Remove the front cover for cleaning the lens
1
Remove the front cover by rotating it anticlockwise.
2
After cleaning, insert the front cover’s lugs into the slits in the unit.
Then rotate the front cover clockwise until it clicks.
中文
使用本机前，请仔细阅读本使用手册并妥善保存以备日后参考。
警告
为减少火灾或电击危险，请勿让本设备受到雨淋或
受潮。
为防止触电严禁拆开机壳，维修请咨询具备资格人
士。
设备不要受到滴水或水溅，不要将盛满液体的花瓶等物品放在设备
上。
警告
本安装应该由有资格的服务⼈员进⾏，并须符合所有当地法规规
定。
警告
此为A级产品。在生活环境中，该产品可能会造成无线电干扰。
在这种情况下，可能需要用户对干扰采取切实可⾏的措施。
注意
特定频率的电磁场可能会干扰本机的图像。
重要
设备铭牌位于顶部。
关于旧产品的处理
请不要将旧的产品与⼀般的生活垃圾⼀同弃置。
正确弃置旧的产品有助于避免对环境和⼈类健康造成潜在的负⾯影响。
具体处理⽅法请遵循当地的规章制度。
特点
SSC-YB411R/YB401R彩色摄像机配备有1/3型
Super HAD CCD II
™*
。
SSC-YB511R/YB501R彩色摄像机配备有1/3型
EXview HAD CCD II
™**
。
其具有以下特点：
镜头焦距为3.1 mm（SSC-YB501R/YB401R）和6.0 mm（SSC-YB511R/
ˎ
ˎ
YB411R）。
高分辨率和高灵敏度
ˎ
ˎ
可切换彩色/黑白模式的白天/夜间功能
ˎ
ˎ
降噪功能
ˎ
ˎ
⾃动白平衡跟踪和调节（ATW）。
ˎ
ˎ
12 V直流电源系统。
ˎ
ˎ
*
Super HAD CCD II
™
是Sony Corporation的商标。（SSC-YB411R/
YB401R）
**
EXview HAD CCD II
™
是Sony Corporation的商标。（SSC-YB511R/
YB501R）
使用须知
电源
SSC-YB511R/YB501R/YB411R/YB401R必须使用12 V直流电源。
-
连接变压器时，请务必将各导线连接⾄适当的端⼝。错误的连接
将导致摄像机发生故障和（或）损坏。
使用本机
请⼩⼼不要溅水或溅洒其他液体在本机上，或使易燃物或⾦属物掉
⼊机内。若在异物进⼊机内的状态下使用本机，摄像机可能会发生
故障或因此发生⽕灾或触电。
操作或存放场所
请勿拍摄⾮常亮的物体（灯光、阳光等）。避免在以下位置使用或
存放摄像机，否则会导致故障。
极热或极冷的地⽅（操作温度：-10℃⾄+50℃）
ˎ
ˎ
长时间暴露于直射阳光下，或者靠近热源（⽐如加热器）的地⽅
ˎ
ˎ
靠近强磁源的位置
ˎ
ˎ
靠近无线电或电视发射器等强电磁辐射源的地⽅
ˎ
ˎ
易于受到强⼒振动或撞击的地⽅
ˎ
ˎ
潮湿或有灰尘的地⽅
ˎ
ˎ
暴露于⾬水的地⽅
ˎ
ˎ
受到荧光灯或窗户反射光影响的地⽅
ˎ
ˎ
在不稳定光线的下⾯（图像会闪烁。）
ˎ
ˎ
结露和高湿的环境
ˎ
ˎ
油烟或油污的环境
ˎ
ˎ
该摄像机不适合室外安装使用，室内安装时也请勿使用防护罩。
ˎ
ˎ
通风
为了避免热量积蓄，不要阻挡摄像机附近的通风。
运送
当运送摄像机时，重新以出⼚时的包装进⾏包装，或用同等品质的
材质包装。
清洁
用吹灰器清除镜头灰尘。
ˎ
ˎ
使用柔软、干燥的布清洁摄像机的外表⾯。要清除顽固的污渍，
ˎ
ˎ
请用少量清洁剂蘸湿软布，然后擦干即可。
不要使用酒精、苯或稀释剂等挥发性溶剂，这些物质可能会破坏
ˎ
ˎ
表⾯光洁度。
有关在摄像机使用过程中出现的任何问题，请与您的Sony维修代理
联系。
有关激光束的注意事项
激光束可能会损伤CCD。如果拍摄包含激光束的场景，请注意不要
让激光束直接射⼊摄像机镜头。
注意
根据电子D/N的性能特性上的特点，在红外线成分较多的光源下，
以及红外线反射率较高的摄影环境下，画⾯⼀部分的颜色还原可能
会发生⼀些偏差。(SSC-YB411R/YB401R)
典型CCD现象
图像中可能出现的以下现象是CCD（电荷耦合器件）图像传感器所特
有的。这些现象不是故障。
白斑
虽然CCD图像传感器是采用高精度技术生产的，但由于宇宙射线等的
影响，其屏幕上可能会出现细⼩的白斑（极少数情况）。
这与CCD图像传感器的原理有关，出现的白斑并不是故障。
在以下情况中，⽐较容易出现白斑：
- 在高温环境下进⾏操作时
- 提高倍率（灵敏度）时
- 当使用慢快门时
垂直拖影
拍摄亮度极高的物体（如强聚光灯或闪光灯）时，屏幕上可能出现
垂直尾线，图像也可能出现扭曲。
监视器屏幕
图像上的垂直拖尾显示
高亮物体（如强聚光灯、强反射光、闪光灯、
阳光）
图形失真
拍摄微⼩的图案、条纹或线条时，它们可能呈锯齿状或出现闪烁现
象。
部件的位置和功能
顶部/前面/右侧
镜头
前盖
三脚架螺丝孔
摄像机的顶部和底部都有用于安装三脚架的
螺丝孔。使用1/4" 20 UNC螺丝将三脚架
安装到摄像机上。三脚架必须放置在平坦的表⾯上，并用手拧紧。
注意
只能使用长度为4.5 mm - 7 mm的安装螺丝。使用其它螺丝可能会
造成不当安装，并可能损坏摄像机内部零件。
后面
VIDEO OUT（复合视频信号输出）连接器（BNC型）
防坠绳安装孔
当将摄像机安装到天花板或墙上时，请务必将防坠绳（⾮附带）固
定到此孔中以确保安全。
DC 12 V（电源输入）端子（DC 12 V ±10%）
安装前盖
拆下前盖以清洁镜头
1
逆时针旋转前盖，将其拆下。
2
清洁后，将前盖的凸舌插⼊本机的狭缝中。
然后顺时针旋转前盖，直⾄听到咔嗒声。
4-424-251-
22
(1)
© 2012 Sony Corporation
Printed in China
Color Video Camera
彩色摄像机
Operating Instructions
使用手册
1/4”, 20 UNC
= 4.5 mm – 7 mm
(ISO standard) (with the
screws fastened)
1/4”, 20 UNC
= 4.5 mm – 7 mm（ISO
标准）（用螺丝固定）
A
1
2
3
B
5
4
6
C
Slit (three sides) /
狭缝（三侧）
Lug (three sides)/
凸舌（三侧）
SSC-YB511R/YB501R
SSC-YB411R/YB401R
