Sony SNC-VB770 Installation Manual Download Page 10

10

Specifications

Camera

Image sensor

35 mm full frame Exmor

®

 CMOS sensor

Number of Effective Pixels

Approx. 12.2 Megapixels

Lens type

E-mount lens (option)

Sync System

Internal synchronization

Minimum Illumination (30 IRE)

0.004 lx (1/30s, F1.4)

Video

Image Compression Format

H.264 (High/Main Profile), JPEG
H.264 (B-picture) supports the resolution below.
3,840 × 2,160
2,880 × 2,160

Maximum Frame Rate

H264: 30 fps (3,840 × 2,160)/30 fps (1,920 × 1,080)
JPEG: 2.5 fps (4,240 × 2,832)

Audio

Compression Format

G.711 (bit rate: 64 kbps, sampling frequency: 8 kHz)
G.726 (bit rate: 40, 32, 24, 16 kbps, sampling frequency: 8 kHz)
AAC-LC (bit rate: 64 kbps, sampling frequency: 16 kHz)
AAC-LC (bit rate: 128 kbps, sampling frequency: 48 kHz)

Interface

Digital Video Output

HDMI (type D) × 1

Microphone Input

Mini jack (monaural, 2.2 k

Ω

, plug-in-power)

Line Input

Mini jack (monaural)

Network port

10BASE-T/100BASE-TX (RJ-45)

Alarm input (sensor input)

2 ports (MAKE contact, BREAK contact)

Alarm output

2 ports (solid-state relay Max. AC 12 V/DC 24 V, 0.4 A) (electrically isolated 
from the camera)

Wireless LAN terminal

Supports the accessory IFU-WLM3 (sold separately)

Memory card slot

SD memory card slot (supports SDHC/SDXC memory cards) × 1

General

Power Requirements

PoE (Compliant with IEEE802.3af)
DC 12 V ± 25 %, AC 24 V ± 20 %, 50/60 Hz

Power Consumption

Max. approx. 16W (including lens)

Operating temperature

When power is turned on
While on

0°C to 50°C
–5°C to +50°C

Storage Temperature

–20°C to +60°C

Operating Humidity

20 % to 80 % (no condensation)

Storage Humidity

20 % to 80 % (no condensation)

Summary of Contents for SNC-VB770












Reviews: