Sony SLV-X9G Operating Instructions Manual Download Page 48

Page: 48 / 96

Recording TV programmes

To stop recording

Press

STOP.

To check the remaining time

Press

DISPLAY. With the display on, press COUNTER/REMAIN to

check the remaining time. Each time you press COUNTER/REMAIN, the
time counter and the remaining time appear alternately. The

indicator

indicates the remaining time.

In order to get an accurate remaining time indication, be sure TAPE
LENGTH in the OPTIONS-1 menu is set according to the tape type you use
(see page 84).

To watch another TV programme while recording

To save a recording

To prevent accidental erasure, break off the
safety tab as illustrated. To record on the
same tape again, cover the tab hole with
adhesive tape.

Press

REC to start recording.

The recording indicator lights up red in the display window.

Press

TV/VIDEO to turn off the VIDEO indicator in the display

window.

Select another programme position on the TV.

REC

LP OPC

VIDEO

Recording indicator

1 : 4

0 : 0 0 : 2

Remaining time

Time counter

Safety tab

Summary of Contents for SLV-X9G

































































































Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands

Sony SLV-X9G, Operating Instructions Manual

Search results

Summary of Contents for SLV-X9G

Reviews:

Related manuals for SLV-X9G

Brands by name

Popular brands