Sony SLV-SF99EN Operating Instructions Manual Download Page 65

Page: 65 / 116

Additional Operations

Checking/changing/cancelling timer settings

When the timer settings overlap

The programme that starts first has priority and the second programme starts
recording only after the first programme has finished. If the programmes start at the
same time, the programme listed first in the menu has priority.

Tip

• In step 5 above, you can check the TIMER LIST by selecting LIST and pressing OK. Press

MENU to exit the TIMER LIST.

Press CURSOR

M/m to select the setting you

want to change or cancel, then press OK.

The selected setting appears in the TIMER
menu.

• To change the setting, press CURSOR

</, to highlight the item you want

to change, and press CURSOR

M/m to reset it.

• To cancel the setting, press CLEAR.

Press MENU.

If any settings remain, turn off the VCR to return to recording standby.

C T

CON F

I R

T I ME R

L P

O K

S P

L P

D A T E

T I M E

PROG.

0 0

: 3 0

VPS
PDC

4. 1

OFF

about 20 seconds

Will be cut off

Programme 1

Programme 2

about 20 seconds will be cut off

Programme 1

Programme 2

Summary of Contents for SLV-SF99EN





















































































































Search results

Summary of Contents for SLV-SF99EN

Reviews:

Related manuals for SLV-SF99EN

Brands by name

Popular brands

Sony SLV-SF99EN, Operating Instructions Manual

Search results

Summary of Contents for SLV-SF99EN

Reviews:

Related manuals for SLV-SF99EN

Brands by name

Popular brands