Sony SLV-SF99EN Operating Instructions Manual Download Page 5

Page: 5 / 116

Setting up the remote commander

Getting Started

Getti

ng Sta

rted

Step 2

Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.

Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.

Using the remote commander

You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (

•

) can be used to operate your

Sony TV. If the TV does not have
the

symbol near the remote

sensor, this remote commander
will not operate the TV.

Remote sensor

[TV]

[VIDEO]

To operate

Set

[TV]

[VIDEO]

the VCR

[VIDEO]

and point at the remote sensor on the VCR

a Sony TV

[TV]

and point at the remote sensor on the TV

continued

Summary of Contents for SLV-SF99EN





















































































































Search results

Summary of Contents for SLV-SF99EN

Reviews:

Related manuals for SLV-SF99EN

Brands by name

Popular brands

Sony SLV-SF99EN, Operating Instructions Manual

Search results

Summary of Contents for SLV-SF99EN

Reviews:

Related manuals for SLV-SF99EN

Brands by name

Popular brands