Sony SLV-SE600A Operating Instructions Manual Download Page 89

Page: 89 / 96

Specifications

ditio

al Inf

ion

Specifications

System

Channel coverage

PAL (B/G)
VHF E2 to E12

VHF Italian channel A to H
UHF E21 to E69

CATV S01 to S05, S1 to S20
HYPER S21 to S41

RF output signal

UHF channels 21 to 69

Aerial out

75-ohm asymmetrical aerial socket

Tape speed

SP: PAL

23.39 mm/s (recording/playback)

NTSC 33.35 mm/s (playback only)

LP: PAL

11.70 mm/s (recording/playback)

NTSC 16.67 mm/s (playback only)

EP: NTSC 11.12 mm/s (playback only)

Maximum recording/playback time

10 hrs. in LP mode (with E300 tape)

Fast-forward and rewind time

Approx. 1 min. (with E180 tape)

Inputs and outputs

LINE-1 (TV)

21-pin

Video input: pin 20
Audio input: pins 2 and 6

Video output: pin 19
Audio output: pins 1 and 3

DECODER/

LINE-2 IN (SLV-SE600E, SX600E,

SE650D, SE700D1/D2/E1/E2, SX700D/E)

21-pin
Video input: pin 20

Audio input: pins 2 and 6

DECODER/

LINE-3 IN (SLV-SE800D1/D2/E,

SX800D)

21-pin

Video input: pin 20
Audio input: pins 2 and 6

LINE-2 IN (SLV-SE800D1/D2/E, SX800D)

VIDEO IN, phono jack (1)

Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative

AUDIO IN, phono jack (2)
Input level: 327 mVrms

Input impedance: more than 47 kilohms

AUDIO OUT (SLV-SE650D, SE700D1/D2/E1/E2,
SX700D/E, SE800D1/D2/E, SX800D)

Phono jack (2)
Rated output level: 327 mVrms

Load impedance: 47 kilohms

Output impedance: less than 10 kilohms

General

Power requirements

220 – 240 V AC, 50 Hz

Power consumption

21 W

Operating temperature

C to 40

Storage temperature

–20

C to 60

Dimensions including projecting parts and controls

Approx. 430 × 100 × 283 mm (w/h/d) (SLV-SE600A/E,
SX600E, SE650D, SE700D1/D2/E1/E2, SX700D/E)

Approx. 430 × 100 × 290 mm (w/h/d) (SLV-SE800D1/
D2/E, SX800D)

Mass

Approx. 4.3 kg (SLV-SE600A/E, SX600E, SE650D,
SE700D1/D2/E1/E2, SX700D/E)

Approx. 4.4 kg (SLV-SE800D1/D2/E, SX800D)

Supplied accessories

Remote commander (1)

R6 (size AA) batteries (2)
Aerial cable (1)

Design and specifications are subject to change without
notice.

Summary of Contents for SLV-SE600A

































































































Search results

Summary of Contents for SLV-SE600A

Reviews:

Related manuals for SLV-SE600A

Brands by name

Popular brands

Sony SLV-SE600A, Operating Instructions Manual

Search results

Summary of Contents for SLV-SE600A

Reviews:

Related manuals for SLV-SE600A

Brands by name

Popular brands