Sony SLV-SE100A1, SLV-SE100A2 Operating Instructions Manual Download

Page: 63 / 92

Setting the recording duration time

Ad
di

tiona

l O
p

era

tions

Setting the recording duration time

To extend the duration

Press

REC repeatedly to set a new duration time.

To cancel the duration

Press

REC repeatedly until the

indicator disappears and the VCR returns to the

normal recording mode.

To stop recording

To stop the VCR while recording, press

STOP.

Note

• You cannot display the current tape time in the display window when setting the recording

duration time.

After you have started recording in the
normal way, you can have the VCR stop
recording automatically after a specified
duration.

While recording, press

REC.

The

indicator appears in the display window.

Press

REC repeatedly to set the duration time.

Each press advances the time in increments of 30 minutes.

The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.

REC

VIDEO

OPC

0:30

1:00

5:30

6:00

Normal recording

Summary of Contents for SLV-SE100A1, SLV-SE100A2





























































































Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands

Sony SLV-SE100A1, SLV-SE100A2, Operating Instructions Manual

Search results

Summary of Contents for SLV-SE100A1, SLV-SE100A2

Reviews:

Related manuals for SLV-SE100A1, SLV-SE100A2

Brands by name

Popular brands