Sony SLV-N70 - Video Cassette Recorder Operating Instructions Manual Download

Page: 42 / 112

Setting up the cable box control (SLV-N80 only)

To ensure correct operation

• Place the Cable Mouse so that it hangs out over the front of the remote sensor on

the cable box or digital satellite receiver.

• Do not place the cable box or digital satellite receiver on top of the VCR.
• Position the cable box or digital satellite receiver away from the VCR.
• Point the remote commander at the VCR, not at the cable box or digital satellite

receiver.

Digital satellite
receiver brand

Code numbers

Sony

650

Hitachi

830

RCA

577

Toshiba

801

Digital satellite
receiver brand

Code numbers

Side view

: Signal flow

Summary of Contents for SLV-N70 - Video Cassette Recorder

















































































































Search results

Summary of Contents for SLV-N70 - Video Cassette Recorder

Reviews:

Related manuals for SLV-N70 - Video Cassette Recorder

Brands by name

Popular brands

Sony SLV-N70 - Video Cassette Recorder, Operating Instructions Manual

Search results

Summary of Contents for SLV-N70 - Video Cassette Recorder

Reviews:

Related manuals for SLV-N70 - Video Cassette Recorder

Brands by name

Popular brands