background image

SERVICE MANUAL

Sony Video & Sound Products Inc.

ACTIVE REAR SPEAKER

9-896-494-01

2018B33-1

© 

2018.02

US Model

Canadian Model

AEP Model

UK Model

Australian Model

Ver. 1.0  2018.02

•  SA-Z9R other than the AUS model is an optional rear 

speaker for exclusive HT-Z9F/ZF9.

•  SA-Z9R of AUS model is a package rear speaker for 

HT-Z9RF.

• Except AUS model
  All of the units included in the right and left rear speak-

ers (SA-LZ9R/RZ9R) and the HT-Z9F (SA-Z9F/SA-
WZ9F/Remote control) or HT-ZF9 (SA-ZF9/SA-WZF9/
Remote control) are required to con

fi

 rming operation of 

this unit. Check in advance that you have all of the units.

• AUS model
  All of the units included in the right and left rear speakers 

(SA-LZ9R/RZ9R) and the HT-Z9RF (SA-Z9F/SA-WZ9F/
Remote control) are required to con

fi

 rming operation of 

this unit. Check in advance that you have all of the units.

SPECIFICATIONS

SA-Z9R

SA-LZ9R/RZ9R

Amplifier section

U.S. models:

POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(FTC)
With 4 ohms loads, both channels driven, from 200 - 
20,000 Hz; rated 20 W per channel minimum RMS power, 
with no more than 1% total harmonic distortion from 

POWER OUTPUT (reference)

50 W (per channel at 4 ohms, 1 kHz)

Except US model:

POWER OUTPUT (rated)

30 W + 30 W (at 4 ohms, 1 kHz, 1% THD)

POWER OUTPUT (reference)

50 W (per channel at 4 ohms, 1 kHz)

Speaker system

Full range speaker system, Acoustic suspension

Speaker

46 mm (1 13/16 in) cone type, Full range speaker

Power requirements

120 V AC, 60 Hz (US, CND)
220 V - 240 V AC, 50 Hz/60 Hz (AEP, UK, AUS)

Power consumption

On: 11 W
Standby mode: 1 W or less
Turned off: 0.5 W or less

Dimensions (w/h/d) (approx.)

100 mm × 155 mm × 100 mm (4 in × 6 1/8 in × 4 in) 
(projecting parts not included)

Mass (approx.)

1.0 kg (2lb 3 3/8 oz)

On copyrights

This product contains software that is subject to the 
GNU General Public License (“GPL”) or GNU Lesser 
General Public License (“LGPL”). These establish that 
customers have the right to acquire, modify, and 
redistribute the source code of said software in 
accordance with the terms of the GPL or the LGPL.

For details of the GPL, LGPL and other software 
licenses, please refer to [Software License 
Information] under 

 [Setup] - [Advanced Settings] 

- [System Settings] on the product.

The source code for the software used in this product 
is subject to the GPL and LGPL, and is available on 
the Web. To download, please access the following:
URL:
http://oss.sony.net/Products/Linux

Please note that Sony cannot answer or respond to 
any inquiries regarding the content of this source 
code.

All other trademarks are trademarks of their 
respective owners.

Wireless transmitter/receiver section

Communication system

Wireless Sound Specification Version 4.0

Frequency band

5 GHz

Modulation method

OFDM

Included items

•  Rear speaker R (1), Rear speaker L (1)
•  Operating Instructions (1)

Radio Frequency Bands and Maximum Output 
Power

Frequency band

Maximum output power

5150 - 5250 MHz 

< 18 dBm

5250 - 5350 MHz

< 18 dBm

5470 - 5600 MHz

< 18 dBm

5650 - 5725 MHz

< 18 dBm

5725 - 5850 MHz

< 13.98 dBm

Rear speaker L-ch

SA-LZ9R

Rear speaker R-ch

SA-RZ9R

Photo:  SA-LZ9R 

(L-ch)

Photo:  SA-RZ9R 

(R-ch)

COMPONENT MODEL NAME (SA-Z9R)

Summary of Contents for SA-LZ9R



































Reviews: