Wireless Speaker
AIR-SA5R
©2009 Sony Corporation Printed in China
4-147-617-
11
(1)
Operating Instructions
Manual de instrucciones
(reverso)
Completely disconnect the unit from
the wall socket (mains) if it is not
going to be used for an extended
period of time.
Should any solid object or liquid get
into the unit, unplug the unit, and
have it checked by qualified
personnel before operating it again.
On placement
Do not place the unit in an inclined
position or in locations that are
extremely hot, cold, dusty, dirty,
humid or lacking adequate
ventilation, subject to vibration,
direct sunlight or a bright light.
Be careful when placing the unit on
surfaces that have been specially
treated (for example, with wax, oil,
polish) as staining or discoloration
of the surface may result.
On heat buildup
Heat buildup in the unit during
operation is normal and is not cause
for alarm.
Do not touch the cabinet if it has
been used continuously at a high
volume because the cabinet may
have become hot.
On the speaker system
This speaker system is not
magnetically shielded, and the picture
on nearby TV sets may become
magnetically distorted. In this
situation, turn off the TV, wait about
15 to 30 minutes, and turn it back on.
If there is no improvement, move the
unit far away from the TV.
Cleaning the cabinet
Clean the cabinet with a soft dry cloth.
Do not use any type of abrasive pad,
scouring powder, or solvent, such as
thinner, benzine, or alcohol.
S-AIR (Sony Audio
Interactive Radio frequency)
Recent times have seen the rapid
spread of DVD media, Digital
Broadcasting, and other high-
quality media.
To ensure that the subtle nuances of
these high-quality media are
transmitted with no deterioration,
Sony has developed a technology
called “S-AIR” for the radio
transmission of digital audio signals
with no compression, and has
incorporated this technology into
the built-in wireless transceiver
EZW-RT10A.
This technology transfers digital
audio signals with no compression
using the 2.4 GHz band range of
ISM band (Industrial, Scientific, and
Medical band), such as wireless
LANs and Bluetooth applications.
After pairing
The connection is established between
the paired main unit and sub unit.
Your system
Neighboring system
Pairing
Sub unit
ID: A
Main unit
Sub unit
ID: A
ID: A
not connected
1
Place the sub unit to be paired
near the main unit.
Pair the main unit with the sub
unit one at a time.
2
Check that the power of the
main unit and the sub unit are
turned on.
3
Check that the S-AIR ID of the
main unit is the same as the
S-AIR ID of the sub unit.
4
Operate the S-AIR main unit to
turn on the pairing function.
For details on turning on the
pairing function, refer to the
Operating Instructions supplied
with the S-AIR main unit.
5
Press the PAIRING button on
the side panel of the unit using
a pointed object.
When pairing is in progress, the
PAIRING indicator on the unit
flashes. When completed, it stays
on.
To cancel pairing
Change the S-AIR IDs of the main unit
and the sub unit to different S-AIR
IDs.
To stop the pairing operation
midway
Press the PAIRING button again.
To pair the main unit with
multiple sub units
Repeat steps 1 through 5.
Operations
WARNING
To reduce the risk of fire
or electric shock, do not
expose this apparatus to
rain or moisture.
To reduce the risk of fire or electric
shock, do not expose this apparatus to
dripping or splashing, and do not place
objects filled with liquids, such as
vases, on the apparatus.
As the main plug is used to disconnect
the unit from the mains, connect the
unit to an easily accessible AC outlet.
Should you notice an abnormality in
the unit, disconnect the main plug
from the AC outlet immediately.
The unit is not disconnected from the
mains as long as it is connected to the
AC outlet, even if the unit itself has
been turned off.
Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet.
The nameplate is located on the
bottom exterior.
Owner’s Record
The model and serial numbers are
located on the bottom of the unit.
Record these numbers in the space
provided below. Refer to them
whenever you call upon your Sony
dealer regarding this product.
Model No.
Serial No.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near
water.
6) Clean only with dry cloth.
7) Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
8) Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus
(including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of
the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit
into your outlet, consult an
electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly
at plugs, convenience receptacles,
and the point where they exit from
the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during
lightning storms or when unused
for long periods of time.
14) Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such as
power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
Consult the dealer or an
experienced radio/TV technician
for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.
For the built-in wireless transceiver
(EZW-RT10A)
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) this
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
This equipment must not be co-located
or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC
radiation exposure limits set forth for
uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65.
This equipment should be installed
and operated with at least 20cm and
more between the radiator and person’s
body (excluding extremities: hands,
wrists, feet and ankles).
“S-AIR” and its logo are trademarks of
Sony Corporation.
The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by Sony Corporation is
under license. Other trademarks and trade
names are those of their respective owners.
iPod is a trademark of Apple Inc.,
registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
All other trademarks and registered
trademarks are of their respective holders.
In this manual,
™
and
®
marks are not
specified.
Features
The AIR-SA5R is an “S-AIR”
compatible product. It is also called the
“S-AIR sub unit.”
It is easy to ready the unit for use. All
you have to do is connect it to a wall
socket.
Connecting the S-AIR main unit
(transmitter product, hereafter called
“main unit”) with the S-AIR sub unit
(receiver product, hereafter called “sub
unit”) using “S-AIR” technology, you
can use each unit in a remote location.
For example, you can install this unit
in a bedroom, and then install the
main unit in the living room. You can
then listen to music from the main unit
located in the living room with this
unit in the bedroom.
This unit is compatible with a main
unit with “MULTI SOURCE” mode,
and the coupling operation. The
coupling operation establishes a
connection between the sub unit and
optional S-AIR remote commander.
Precautions
Notes on use of the S-AIR
product
As the S-AIR product transmits
sound by radio waves, sound may
skip when radio waves are
obstructed. This is a characteristic of
radio waves and is not a
malfunction.
As the S-AIR product transmits
sound by radio waves, equipment
that generates electromagnetic
energy, such as a microwave oven,
may interfere with sound
transmission.
As the S-AIR product uses radio
waves that share the same frequency
as other wireless systems, such as
wireless LAN or Bluetooth devices,
interference or poor transmission
may result. In this case, take the
following steps:
Do not install the S-AIR product
near other wireless systems.
Do not use the S-AIR product
and other wireless systems at the
same time.
The transmission distance differs
depending on the usage
environment. Find a location where
transmission between the unit and
the S-AIR main unit is most
effective, and install the unit and the
S-AIR main unit there.
On safety
Operate the unit only on the power
sources specified in “Specifications”.
Hooking up the unit
S-AIR ID selector
Set the same S-AIR ID for this unit and
the S-AIR main unit to be connected.
For details on setting the S-AIR ID, see
“Establishing the connection with an
S-AIR main unit.”
Remote Sensor
The optional
*
S-AIR remote
commander (AIR-RM10) can operate
/
(power), /–, and
COUPLING with this unit.
Hook-and-loop fastener
: The hook-and-loop fastener is
attached to the unit.
: Attach the hook-and-loop fastener
in the following way.
Clean the area where the hook-
and-loop fastener is to be
attached beforehand. (If you
fail to do so, the hook-and-loop
fastener may detach.)
Getting Started
/
(power)
VOL (Volume) +*/–
S-AIR CH+
POWER indicator
*
VOL + has a tactile dot.
Peel off the bottom sheet on the
adhesive side of the supplied
hook-and-loop fastener. Attach
it to the prepared area of the
wall socket and press it firmly.
Tips
- Allow some space between the
hook-and-loop fastener and the
blades of the plug.
- Make sure to attach the hook-and-
loop fastener where it can support
the unit securely.
Power
Connect the unit to a wall socket.
Notes
Do not use the unit with a wall socket that
is located in a high place.
Hold the unit when pressing buttons to
avoid stressing the plug blades in the wall
socket.
Establishing the
connection with an S-AIR
main unit
Connect the unit and S-AIR main unit
to listen to sound from the S-AIR main
unit.
You can easily establish the connection
by setting the same S-AIR ID for this
unit and S-AIR main unit.
1
Operate the S-AIR main unit to
turn on the S-AIR function.
For details on turning on the S-AIR
function, refer to the Operating
Instructions supplied with the
S-AIR main unit.
2
Set the S-AIR ID of the unit to
the same S-AIR ID as the S-AIR
main unit to be connected.
For details on setting the S-AIR ID
of the S-AIR main unit, refer to the
Operating Instructions supplied
with the S-AIR main unit.
3
Press
to turn on the unit.
Once the connection is established,
the S-AIR indicator on the unit
lights up.
Identifying the main unit with
a specific sub unit (Pairing
operation)
It is easy to set the same S-AIR ID for
the main unit and the sub units to
establish the connection.
However, if a neighbor has an S-AIR
main unit with the same S-AIR ID as
your S-AIR main unit, the neighbor
may be able to hear the audio
transmitted from your S-AIR main
unit on the neighbor’s system. Also,
you may be able to hear the audio
transmitted from your neighbor’s
S-AIR main unit on your system. To
prevent this, you can identify the main
unit with a specific sub unit by
performing the pairing operation.
Before pairing
The connection is established by the
S-AIR ID (example).
Your system
Neighboring system
ID: A
Main unit
Sub unit
Sub unit
ID: A
ID: A
Listening to the sound of
the connected S-AIR main
unit
You can use the S-AIR function to
listen to the sound of an S-AIR main
unit in a remote location.
1
Perform the procedure
described in “Establishing the
connection with an S-AIR main
unit” and check that the S-AIR
indicator is lit.
2
Press S-AIR CH + repeatedly to
select the desired S-AIR channel
of the S-AIR main unit.
The S-AIR channels that can be
selected depend on the S-AIR main
unit. For details, refer to the
Operating Instructions supplied
with the S-AIR main unit.
3
Operate S-AIR main unit or the
optional* S-AIR remote
commander to start playback.
4
Press VOL +/– to adjust the
volume.
To operate the S-AIR main unit
from the unit
You can perform the following
operations using the buttons on the
unit.
To
Press
Select sound source.
S-AIR CH +
Adjust the volume.
VOL +/–
Depending on the connected S-AIR
main unit, the operation may differ.
Refer to the Operating Instructions of
the S-AIR main unit.
Note
You cannot use this unit as a subwoofer or
surround speaker with other Sony S-AIR
components.
Advanced Operations
Enjoying different sound
source with multiple sub
units
Use the main unit that can set the
MULTI SOURCE mode.
When selecting the MULTI SOURCE
mode, you can listen to different sound
source with each sub unit.
For setting up and details, refer to the
Operating Instructions of the main
unit.
To identify the unit using the
optional* S-AIR Remote
commander AIR-RM10
(Coupling operation)
This unit is compatible with the
coupling operation. The coupling
operation establishes a connection
between the sub unit and optional
*
S-AIR remote commander. For details,
refer to the Operating Instructions of
the optional
*
S-AIR remote
commander.
When the coupling operation is in
progress, the CPL indicator on the unit
flashes. When completed, it stays on.
Notes
The AIR-RM10 can operate
/
(power),
/–, and COUPLING with this
unit.
In the following cases, the CPL indicator
turns off:
- If the S-AIR main unit is not compatible
with the MULTI SOURCE mode.
- If the S-AIR main unit is not compatible
with the coupling operation.
- If processing of the coupling operation is
failed.
For details on coupling operation, refer to
the Operating Instructions of the AIR-RM10.
Troubleshooting
1
Make sure the unit is correctly
and firmly connected to a wall
socket.
2
Find your problem in the
checklist below, and take the
indicated corrective action.
If the issue persists, contact your
nearest Sony dealer.
When bringing this unit in for
repairs, be sure to bring in the entire
system (this unit, the S-AIR main
unit).
This product is a system product,
and the entire system is needed to
determine the location requiring
repair.
The S-AIR indicator is turned off.
Check that the unit is connected to a
wall socket securely and the unit is
turned on.
Connecting the unit and S-AIR
main unit is not possible. (The
S-AIR indicator flashes.)
If you use another S-AIR main unit,
place it more than 8 m (26
1
/
4
feet)
away from the S-AIR main unit you
are using.
Confirm the S-AIR IDs of the unit
and the S-AIR main unit.
The main unit is paired with another
S-AIR sub unit. Pair the main unit
with the sub unit you are using.
The main unit is paired with another
S-AIR sub unit. Cancel pairing.
Place so that the unit and the S-AIR
main unit are separated from other
wireless devices.
Stop using any other wireless
devices.
The connected S-AIR main unit is
turned off. Turn on the S-AIR main
unit.
The S-AIR channel fails to
change.
Check that the unit and the S-AIR
main unit are connected properly.
When using the Wireless Audio
Transmitter for PC as the S-AIR
main unit, sub unit operations will
not be functional if supplied PC
application is not booted or
Standard Mode is selected.
There is no sound.
If you use another S-AIR main unit,
place it more than 8 m (26
1
/
4
feet)
away from the S-AIR main unit you
are using.
Confirm the S-AIR IDs of the unit
and the S-AIR main unit.
Check the pairing setting.
Place so that the unit and the S-AIR
main unit are closer.
Stop using any equipment that
generates electromagnetic energy,
such as a microwave oven.
Place so that the unit and the S-AIR
main unit are separated from other
wireless devices.
Stop using any other wireless
devices.
Change the S-AIR ID settings of the
unit and the S-AIR main unit.
Turn off the unit and S-AIR main
unit and then turn them on again.
Check that the unit is connected to a
wall socket securely and the unit is
turned on.
Increase the volume of the unit.
There is noise or the sound
skips.
If you use another S-AIR main unit,
place it more than 8 m (26
1
/
4
feet)
away from the S-AIR main unit you
are using.
Place so that the unit and the S-AIR
main unit are closer.
Stop using any equipment that
generates electromagnetic energy,
such as a microwave oven.
Place so that the unit and the S-AIR
main unit are separated from other
wireless devices.
Stop using any other wireless
devices.
Change the S-AIR ID settings of the
unit and the S-AIR main unit.
Do not place a mobile phone near
the unit and the S-AIR main unit, as
this may result in noise.
Specifications
Amplifier section
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 4 ohms loads, both channels
driven, from 100 – 10,000Hz; rated 1.5
watts per channel minimum RMS
power, with no more than 10% total
harmonic distortion.
Continuous RMS power output
(reference): 2.5 watts (4 ohms at 1 kHz,
10% harmonic distortion)
Speaker section
Speaker system: Full range, bass-reflex
type
Speaker units: 39 mm (1
9
/
16
in), cone
type (1)
Nominal impedance: 4 ohms
Built-in wireless transceiver
(EZW-RT10A)
Communication System: S-AIR
Specification version 1.0
Frequency band: 2.4000 GHz
2.4835 GHz
Modulation method: DSSS
Power requirements: DC 3.3 V,
350 mA
Dimensions (w/h/d): 50 × 13 × 60 mm
(2 ×
17
/
32
× 2
3
/
8
in)
Mass: 24 g (1 oz)
General
Power requirements: 120 V AC, 60 Hz
Power consumption: 4 watts
Dimensions (w/h/d): Approx. 80 ×
166 × 62 mm (3
1
/
4
× 6
5
/
8
× 2
1
/
2
in)
Mass: Approx. 380 g (13.4 oz)
Supplied accessories:
Hook-and-loop fastener (1)
Design and specifications are subject
to change without notice.
*
The optional S-AIR remote
commander is included in the
package product.
