C:\2629955E11RDRHX910E32\GB10OTH-
E32.fm
master page=left
RDR-HX910
2-629-955-
E1
(1)
90
Program Edit
*
1
*
2
*
3
*
4
*
5
*
6
You can select scenes from a DV (digital video)/
Digital8 format tape, and then automatically
record selected scenes to the HDD (hard disc
drive) or a DVD (digital video disc).
To use this function, you will do the following:
m
Using the recorder’s remote control, fast forward
or rewind the tape to select the scenes. At this
point, the selected scenes are not copied to the
disc. The recorder only remembers the IN (in) and
OUT (out) points of the scenes that you selected
for dubbing. You can also reset, erase, or change
the order of the scenes.
m
After you have selected the scenes, the recorder
will fast forward and rewind the tape
automatically and record the scenes to the HDD
(hard disc drive) or a DVD (digital video disc).
How chapters are created
The contents dubbed to the HDD (hard disc drive) or
DVD (digital video disc) become a single title.
When “Auto Chapter” of “Features” setup is set to
“On,” this title is divided into chapters. When
dubbing to the HDD (hard disc drive) or a DVD-
RW (VR mode) (digital video disc-rewritable,
minus RW (Video Recording mode)), each shooting
session on the tape becomes a chapter on the disc.
For other discs, the recorder divides the title into
chapters at approximately 6 minute intervals.
*
1
HDD (hard disc drive).
*
2
DVD+RW (digital video disc-rewritable, plus RW).
*
3
DVD-RW (VR mode) (digital video disc-rewritable,
minus RW (Video Recording mode)).
*
4
DVD-RW (Video mode) (digital video disc-
rewritable, minus RW (Video mode)).
*
5
DVD+R (digital video disc-recordable, plus R).
*
6
DVD-R (digital video disc-recordable, minus R).
1
Follow steps 1 to 5 of “Preparing for DV
(digital video)/Digital8 dubbing” on
page 87, and press SYSTEM MENU
(system menu).
2
Select “DV/D8 EDIT,” and press ENTER
(enter).
The display asks if you want to start selecting
scenes.
• If you have previously saved a program, the
display asks if you want to edit an existing
program or to create a new program. To
resume editing the existing program, select
“Saved Data,” and go to step 6.
3
Select “Start,” and press ENTER (enter).
The display for setting the IN (in) point (start
of the scene) appears.
The scene starts to play in the background.
4
Select the IN (in) point by pressing
m
/
M
, and press ENTER (enter).
The display for setting the OUT (out) point
(end of the scene) appears. The scene starts to
play in the background from the IN (in) point.
5
Select the OUT (out) point by pressing
m
/
M
, and press ENTER (enter).
The display asks if you want to add the
selected scene to the Scene List menu.
To preview the scene, select “Preview.”
To reset either the IN (in) or OUT (out) point,
select “Change IN” or “Change OUT,” and
repeat from step 4.
Connect your digital video camera and
prepare for recording
Select and edit the scenes you want to dub
Dub the selected scenes
HDD
+
RW
-RW
VR
-RW
Video
+
R
-
R
Scene Selection
Do you want to select a scene?
Start
Cancel
Select scene(Set IN point)
Controlling...
Scenes Selection
Do you want to capture the scene
OK
Cancel
Preview
Change IN
Change OUT
0:00:30
between IN
and OUT 0:00:52?
