Sony PWS-4500 Operation Manual Download

Page: 9 / 63

Chapter

Chapt

Set

Connecting External Devices

Setup

Connecting External
Devices

This section describes how to connect the unit to external
devices to record or play back data. This section describes
the configuration with ports A and C used for inputs and
ports B and D used for outputs.

Using the unit as a recorder

The following shows an example of connecting a 4K
digital player or other devices to the input ports and using
the unit as a recorder.

Using a common time code

On this unit, a common time code can be used for multiple
input ports.
To use a common time code, set the master time code in
Master TC

(page 20)

on the Setup tab of the web menu,

then set “Master TC” in TCG Source

(page 30)

for each

input port on the Port screen.

4K digital player

Video monitor

Remote controller

Summary of Contents for PWS-4500
































































Search results

Summary of Contents for PWS-4500

Reviews:

Related manuals for PWS-4500

Brands by name

Popular brands

Sony PWS-4500, Operation Manual

Search results

Summary of Contents for PWS-4500

Reviews:

Related manuals for PWS-4500

Brands by name

Popular brands