12
Front Panel
Chap
te
r 2
Name
s
an
d
F
u
nc
tio
n
s
o
f Pa
rt
s
a
CH-1/ALL CH, CH-2 to CH-4 (audio level)
adjustment knobs
Depending on the setting of the VARIABLE switch, these
adjust the input audio or playback audio levels of channels
1 to 4.
You can adjust levels of channels 5 to 8 using the function
menu.
For details, see page 41.
By setting setup menu item 131 AUDIO VOLUME, you
can enable the CH-1/ALL CH adjustment knob to
simultaneously adjust all eight channels. When this
simultaneous adjustment is enabled, the ALL CH indicator
lights.
b
VARIABLE (audio level adjustment selector)
switch
This selects whether the input audio level or playback
audio level is adjusted when using the CH-1/ALL CH and
CH-2 to CH-4 adjustment knobs to adjust channels 1 to 4,
and when using the function menu to adjust channels 5 to
8.
REC:
Adjust the input audio levels. The playback audio
levels are fixed at their preset values.
PRESET:
The audio levels are fixed at their preset values.
PB:
Adjust the playback audio levels. The input audio
levels are fixed at their preset values.
3
Arrow buttons
The four arrow buttons can also be used as the MARK1
button, MARK2 button, IN button, and OUT button. The
correspondence with these buttons is as follows.
V
button:
MARK1 button
v
button:
MARK2 button
B
button:
IN button
b
button:
OUT button
You can use these buttons for thumbnail selection, menu
setting operations, setting IN/OUT points, and so on.
a
V
/MARK1 button and
v
/MARK2 button
When the clip list screen is shown on the display, you can
use these for thumbnail selection.
During recording or playback, a shot mark 1 or shot mark
2 is recorded as an essence mark when you press the PUSH
SET knob with the
V
/MARK1 or
v
/MARK2 button held
down.
You can delete essence marks on the chapter thumbnail
screen
.
b
IN indicator and OUT indicator
Lights or flashes as follows when you set IN and OUT
points in the clip to copy only the part defined by the IN
and OUT points
IN indicator:
When an IN point is set, this lights. If an
attempt is made to set the IN point after a recorded
OUT point, this flashes.
OUT indicator:
When an OUT point is set, this lights. If
an attempt is made to set the OUT point before a
recorded IN point, this flashes.
c
B
/IN button and
b
/OUT button
When the clip list screen is shown on the display, you can
use these for thumbnail selection.
An IN or OUT point is set when you press the PUSH SET
knob with the
B
/IN or
b
/OUT button held down. The IN
or OUT point setting is deleted when you press the
RESET/RETURN button with the
B
/IN or
b
/OUT button
held down.
4
Shuttle/jog/variable control section
a
SHTL/JOG (shuttle/jog)/FOLDER SEL (folder
select) button
Functions as the SHTL/JOG button or the FOLDER SEL
button.
SHTL/JOG button:
Press this button, turning it on, to
perform shuttle or jog playback.
FOLDER SEL button:
When a USB drive is connected,
press this button to display a list of the folders on the
USB drive.
b
VAR/JOG (variable/jog)/MEDIA SEL (media
select) button
Functions as the VAR/JOG button or the MEDIA SEL
button.
VAR/JOG button:
Press this button, turning it on, to
perform variable or jog playback.
MEDIA SEL button:
When a USB drive is connected,
press this button to select the target media (disc or
USB drive).
MARK2
MARK1
IN
OUT
L/JOG
1
V
/MARK1 button and
v
/MARK2 button
2
IN indicator and OUT indicator
3
B
/IN button and
b
/OUT button
RETURN
RESET
1
SHTL/JOG)/FOLDER SEL button
2
VAR/JOG/MEDIA SEL button
3
Jog/shuttle transport indicators
5
Jog dial
4
Shuttle dial