Sony PCG-8A8M User Manual Download

Page: 83 / 119

Sony Notebook

User Guide

Connecting peripheral devices

Connecting to a network (LAN)

You can connect your computer or port replicator to 10BASE-T/100BASE-TX-type networks via an Ethernet
network cable. For the detailed settings and devices needed to connect to the network, consult your
Network Administrator.

✍

The default settings make your computer able to connect to

the network.

If the main unit is docked, you can only use the Ethernet network
connector on the port replicator.

For more information about connecting your notebook to the
network, please consult the Hardware troubleshooting section of
the VAIO-Link website:

How to troubleshoot network problems

Do not plug a phone cable into the Ethernet network connector.

Summary of Contents for PCG-8A8M
























































































































Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands

Sony PCG-8A8M, User Manual

Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands