Sony PCG-8A8M User Manual Download

Page: 38 / 119

Sony Notebook

User Guide

Using your notebook

n N

The

Jog Dial

™ window is always displayed on the screen. This window has two modes: Launcher mode and

Guide mode.

The

Jog Dial

™ window is in Launcher mode until you start an application or

the

Jog Dial

™ window becomes active. When an arrow appears next to an

item in the

Jog Dial

™ window, you can display a submenu for that item by

selecting it and pressing the Jog Dial™.

The

Jog Dial

™ window switches to Guide mode when you start an

application and its window becomes active. Depending on the application,
the Jog Dial™ window displays different commands that you can select or
execute by rotating or pressing the Jog Dial™.

✍

You can adjust the size of the

Jog Dial

™ window or close it. To display the

Jog Dial

™ window, double-

click

in the system tray.

Summary of Contents for PCG-8A8M
























































































































Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands

Sony PCG-8A8M, User Manual

Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands