NW-ZX300/ZX300A
©2017 Sony Corporation Printed in Malaysia
English
About the manuals
1. Instruction Manual (this manual)
2.
(Startup Guide)
The Startup Guide describes the following:
• Basic operating instructions of your WALKMAN®
• How to access useful PC applications websites on the internet
3. Help Guide (web document for a PC/smartphone)
The Help Guide contains more detailed operating
instructions, specifications and customer support
website URL, etc.
http://rd1.sony.net/help/dmp/nwzx300/h_ww/
While browsing is free, you may be charged a
communication fee according to your carrier contract.
Depending on the country/region in which you have purchased your
Walkman, some models may not be available.
Notes for using Walkman
Note for battery
• To prevent deterioration of the battery, charge the battery at least
once every 6 months.
Formatting a microSD card
Be sure to read the instructions for microSD cards in the Help Guide on
the Internet before you store content on a microSD card (not supplied).
BLUETOOTH® capabilities
You can listen to music stored on your Walkman from Bluetooth audio
devices such as headphones or speakers.
Pairing (first time the device is used)
When you connect Bluetooth audio devices wirelessly for the first time,
the devices must be registered to each other. This registration is called
“pairing.”
1. Set the Bluetooth audio device to pairing mode. (Refer to the
device’s instruction manual.)
2. Tap
– [
Settings] – [Connect to/Add Audio Device] under
[Bluetooth].
3. Tap the Bluetooth switch to turn on the Bluetooth function.
4. Tap [Add Device (Pairing)] to start pairing.
5. Select the device from the paired device list to make the Bluetooth
connection.
After the Bluetooth connection is established, [Connected] is
displayed.
Connecting (subsequent uses)
1. Turn on the paired Bluetooth audio device and set it to standby.
2. Tap
– [
Settings] – [Connect to/Add Audio Device] under
[Bluetooth].
3. Tap the Bluetooth switch to turn on the Bluetooth function.
4. Select the device from the paired device list to make the Bluetooth
connection.
Disconnecting
1. Tap
– [
Settings] – [Connect to/Add Audio Device] under
[Bluetooth].
2. Tap the connecting device name on the paired device list, and tap
[OK] on the disconnection dialog.
Turning the Bluetooth function on or off
1. Tap
– [
Settings] – [Connect to/Add Audio Device] under
[Bluetooth].
2. Tap the Bluetooth switch to turn on or off.
Turning the NFC function on or off
1. Tap
– [
Settings].
2. Tap [NFC] under [Bluetooth] and add or remove a check mark to turn
the NFC function on or off.
Note
• Pairing information is deleted in the following situations. Pair the devices again.
– One or both of the devices are reset to the factory settings.
– Pairing information is deleted from the devices, such as when the devices are
repaired.
Troubleshooting
Your Walkman cannot charge the battery or is not recognized on
your computer.
• The USB cable (supplied) is not connected to a USB connector
on your computer properly. Disconnect the USB cable, and then
reconnect it.
• The charge lamp on the Walkman lights up in red while the battery is
charging, and goes off when the charging is completed.
• When you use your Walkman for the first time, or if you have not
used the Walkman for a long time, it may take a few minutes to be
recognized by the computer. Check that the computer recognizes the
Walkman after you have connected it to the computer for about 10
minutes.
• If the approaches listed above fail to resolve the issue, turn off
your computer completely and disconnect your Walkman. Then
disconnect the power cable, battery, and anything else connected
to the computer and discharge it for five minutes. After discharging,
turn on the computer again and reconnect the Walkman.
Compliance & Information
Information on laws and trademarks
• For information on laws, regulations and trademark rights, refer to
“Important Information” contained in the supplied software. To read
it, install the supplied software on your computer.
To install it, open [WALKMAN] in your Walkman’s system storage
after connecting to your computer.
Windows user: [FOR_WINDOWS] - [Help_Guide_Installer(.exe)]
Mac user: [FOR_MAC] - [Help_Guide_Installer_for_mac]
After installing the software, double-click the shortcut or the alias
icon generated on your desktop.
• The N-Mark is a trademark or registered trademark of NFC Forum, Inc.
in the United States and in other countries.
About the in-ear headphones
• When you use in-ear headphones with a high degree of adhesion,
note the following. Otherwise, you may damage your ears or
eardrums.
– Do not insert the earbuds forcefully into your ears.
– Do not remove the earbuds from your ears suddenly. When you
take off the headphones, move the earbuds up and down gently.
About the headphones
• Avoid playing the unit at so loud a volume that extended play might
affect your hearing.
• At a high volume outside sounds may become inaudible. Avoid
listening to the unit in situations where hearing must not be
impaired, for example, while driving or cycling.
• As the headphones are of open-air design, sounds go out through
the headphones. Remember not to disturb those close to you.
Design and specifications are subject to change without notice.
4-698-040-
42(1)
Instruction Manual
数码音频播放器
出版日期：
2017年12月
说明书手册
CS
简体中文
使用产品前请仔细阅读本使用说明书，并请妥
善保管
请勿把本机安装在书橱或嵌入墙壁的机架内。
请勿将电池（安装的电池组或多个电池）长时
间暴露在直射阳光、火焰或类似的过热热源附
近。
关于手册
1. 说明书手册（本手册）
2.
（入门指南）
入门指南描述下列内容 ：
•
您的 WALKMAN
®
的基本使用说明
•
如何访问互联网上有用的电脑应用程序网站
3. 帮助指南（电脑 / 智能手机用网络
文档）
帮助指南包含更详细的使用说明、规
格和客户支持网站 URL 等。
http://rd1.sony.net/help/dmp/nwzx300/h_ww/
虽然浏览是免费的，但根据您的运营商合同，
您可能会被收取通信费。
根据您购买 Walkman 的国家 / 地区的不同，可
能不提供某些型号。
有关使用 Walkman 的注意事项
有关电池的注意事项
•
为防止电池性能降低，请每六个月对电池至
少充电一次。
格式化 microSD 卡
在 microSD 卡（不提供）上存储内容之前，请
务必阅读互联网上帮助指南中有关 microSD 卡
的说明。
BLUETOOTH
®
功能
可以从耳机或扬声器等 Bluetooth 音频设备收
听存储在 Walkman 上的音乐。
配对（首次使用设备时）
当您第一次无线连接 Bluetooth 音频设备时，
必须互相注册设备。此注册被称为 “配对”。
1. 将 Bluetooth 音频设备设置为配对模式。（参
阅设备的说明书手册。）
2. 点击
–［ 设置］–［Bluetooth］下的［连
接到 / 添加音频设备］。
3. 点击 Bluetooth 开关打开 Bluetooth 功能。
4. 点击［添加设备 ( 配对 )］开始配对。
5. 从已配对设备列表中选择设备进行 Bluetooth
连接。
建立 Bluetooth 连接后，会显示［已连接］。
