manualshive.com logo in svg

Sony MCC3000MT, Instructions For Use Manual

Share
Download
Sony MCC3000MT Instructions For Use Manual Download Page 17

Connection between the Camera Head and CCU

17

P

repa

ra

ti

ons

Connect the camera cable connector on the 
camera head with the CAMERA A/B connector 
on the CCU using the optional CCMC-T05/T10/
T20 Camera Cable.

Notes

• Be sure to turn off the power supply for all 

equipment when you connect or disconnect the 
camera cable. Connecting/disconnecting a 
cable while the power is on may result in 
malfunctions.

• Be sure to connect the camera head and CCU 

with the camera cable before you start the unit.

• Insert the connector by pushing it straight in, 

being careful not to bend the pins.

• Insert the connectors of the cables properly. 

Loose connection often generates noise. When 
pulling out a cable, be sure to pull it out by the 
connector, not the cable itself.

1

Align the positioning marks on the 
camera cable connector and on the 
camera cable round plug, and then push 
the plug in.

2

Turn the connector ring to tighten.

1

Connect the camera cable square plug 
to the CAMERA A connector.

2

Tighten the two screws on the square 
plug.

Connect the camera cable to the CAMERA B 
connector in the same way.

Notes

• Excessive tightening the screws may make 

them difficult to loosen and result in damage.

• Turning the screws with your hands until the 

screws do not move is sufficient. Do not use 
tools or excessive force when tightening the 
screws.

Connection between the 
Camera Head and CCU

Connecting the camera cable to 
the camera head

Connector ring

Positioning marks

Connecting the camera cable to 
the CAMERA A/B connector

Summary of Contents for MCC3000MT

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands