manualshive.com logo in svg

Sony LT39h, Troubleshooting Manual

Introducing the Sony LT39h Troubleshooting Manual - a comprehensive, user-friendly guide designed to assist you in resolving any technical issues you may encounter with your device. This must-have manual is available for free download from manualshive.com, offering invaluable solutions to enhance your Sony LT39h experience.

Share
Download
background image

 

 

Troubleshooting Guide (mech)   

1277-9814  Rev 

2 

 Sony Ericsson Mobile Communications AB – Company Internal                                                        

53(63) 

 

Problem Areas 

 

1.31  TV-Out Test 

1.31.1 TV-Out test fails 

 
Check: 

Inspect the USB connector. 

Action: 

1. If dirty or oxidized – clean the connector. 
2. Replace Main PBA. 

 

Summary of Contents for LT39h
































































Reviews:

No comments

Related manuals for LT39h

Patton electronics SL4050/B12/E Getting Started Manual preview
SL4050/B12/E
Brand: Patton electronics Pages: 79
Yealink W56P Telesystem Quick Start Manual preview
W56P Telesystem
Brand: Yealink Pages: 12
Yealink Verizon One Talk W60B Quick Reference Manual preview
Verizon One Talk W60B
Brand: Yealink Pages: 8
Yealink Telkom W52P Specification preview
Telkom W52P
Brand: Yealink Pages: 2
Yealink T46S Skype for Business Handling Instruction preview
T46S Skype for Business
Brand: Yealink Pages: 2
Yealink VP59 Teams Administrator'S Manual preview
VP59 Teams
Brand: Yealink Pages: 533
HTC Touch 3G User Manual preview
Touch 3G
Brand: HTC Pages: 76
Telesis ITS821 Installation And User Manual preview
ITS821
Brand: Telesis Pages: 11
NAPCO StarLink Full Data SL-1FD-T Datasheet preview
StarLink Full Data SL-1FD-T
Brand: NAPCO Pages: 2
Unimax MAXAlpha User Manual preview
MAXAlpha
Brand: Unimax Pages: 95
Xiaomi Mi 9T User Manual preview
Mi 9T
Brand: Xiaomi Pages: 9
GENERAL MOBILE discovery Manual preview
discovery
Brand: GENERAL MOBILE Pages: 56
SoftBank 202SH User Manual preview
202SH
Brand: SoftBank Pages: 98
iiNet BizPhone Premium T48U User Manual preview
BizPhone Premium T48U
Brand: iiNet Pages: 26
Zte F100 User Manual preview
F100
Brand: Zte Pages: 54
Sigma mobile X-treme PQ54 User Manual preview
X-treme PQ54
Brand: Sigma mobile Pages: 34
1life air User Manual preview
air
Brand: 1life Pages: 4
G-Tide G150I User Manual preview
G150I
Brand: G-Tide Pages: 24

Brands by name

Popular brands

Load more brands