Sony LT39h Troubleshooting Manual Download Page 21 | Manualshive

Page: 21 / 63

background image

Troubleshooting Guide (mech)

1277-9814 Rev

2



Sony Ericsson Mobile Communications AB – Company Internal

21(63)

Problem Areas: Microphone

Check:

Inspect the microphone on the FPC Assembly Relay.

Action:

1. If clogged – clean it.
2. If the microphone is damaged – replace the FPC
Assembly Relay.

Check:

Inspect the BtB connector of FPC Assembly Relay to Main
PBA.

Action:

1. If not properly connected – disconnect and reconnect it.
2. If dirty or oxidized – clean it.

3. If the BtB connector of FPC Assembly Relay or FPC is
damaged – replace the FPC Assembly Relay.
4. Replace Main PBA.

1.8.2 Secondary Microphone

Check:

Inspect the external port of secondary microphone on the
Rear Cover Assy.

Action:

1. If clogged – clean it.

«
...
19
20
21
22
23
...
»

Summary of Contents for LT39h
































































Reviews:

No comments

Related manuals for LT39h

Brand: NEC Pages: 36

Brand: NEC Pages: 4

Brand: NEC Pages: 3

Brand: Kalley Pages: 32

Brand: Samsung Pages: 135

Brand: HTC Pages: 10

Brand: NEC Pages: 72

Brand: Hanlong Pages: 68

Brand: i.safe MOBILE Pages: 72

Brand: Point Mobile Pages: 8

Brand: Lephone Pages: 23

Brand: Meriam Pages: 31

Brand: Yezz Pages: 80

Brand: Pantech Wireless Pages: 71

Brand: ALIGATOR Pages: 20

Brand: 2N Pages: 12

Brand: Huawei Pages: 90

Brand: Huawei Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands