background image

KDL-22EX355/32EX355/40EX455  

16

Components  not  identified  by  a  part  number  or 

description are not stocked because they are seldom 

required for routine service.

The component parts of an assembly are indicated by the 

reference numbers in the far right column of the parts list 

and within the dotted lines of the diagram.

Items marked with an asterisk are not stocked since 

they are seldom required for routine service.  Expect 

some delay when ordering  these components.

NOTE: The components identified by shading 

and 

!

 mark are critical for safety. Replace only 

with part number specified. 

NOTE: The components identified by a red outline and a 

 mark contain 

confidential information. Specific instructions must be adhered to whenever 

these components are repaired and/or replaced. 

See Appendix A: Encryption Key Components in the back of this manual. 

SECTION 4 - DISASSEMBLY/PART NUMBER INFORMATION

TABLE-TOP STAND AND REAR COVER REMOVAL

A

  Gently place the LCD TV face down onto a soft cloth and remove 3 screws from the bottom of Table-Top Stand.

B

  To avoid damaging the AC Power Supply Cord, remove the screw from the AC Cover and disconnect the AC Power 

Cord.

 

 

REF. NO.  

PART NO. 

DESCRIPTION 

[ASSEMBLY INCLUDES]

 

REF. NO.  

PART NO. 

DESCRIPTION 

[ASSEMBLY INCLUDES]

 

4-438-330-01 

REAR COVER (22IRST)   

[2]

 

 

 

(KDL-22EX355 ONLY)

 

4-438-331-01 

REAR COVER (32IRST)   

[2]

 

 

 

(KDL-32EX355 ONLY)

 

4-438-332-01 

REAR COVER (40IRST)   

[2]

 

 

 

(KDL-40EX455 ONLY)

 

4-421-136-01 

BRACKET, VESA (22IRST)

 

 

 

(KDL-22EX355 ONLY)

 

4-421-137-01 

BRACKET, VESA (32IRST)

 

 

 

(KDL-32EX355 ONLY)

 

4-421-138-01 

BRACKET, VESA (40IRST)

 

 

 

(KDL-40EX455 ONLY)

 

4-421-151-01 

COVER, AC (IRST)

!

  4 

1-846-276-11 

POWER SUPPLY CORD

 

X-2585-274-1 

TABLE STAND ASSEMBLY (22IRST)

 

 

 

(KDL-22EX355 ONLY)

 

X-2585-275-1 

TABLE STAND ASSEMBLY (32IRST)

 

 

 

(KDL-32EX355 ONLY)

 

X-2585-276-1 

TABLE STAND ASSEMBLY (40IRST)

 

 

 

(KDL-40EX455 ONLY)

 

X-2584-211-1 

BAG ASSEMBLY, SCREW

 

 

 

(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV)

 

  

For product protection and safety reasons, Sony strongly recommends that

 

 

you use the screws provided with the TV.

  

CAUTION: These screws cannot be used to secure the TV to the Wall

 

 

 

Mount Brackets.

C

  Remove the remaining screws from the Rear Cover.

D

  Gently hold down the Rear Cover from the center, 

then carefully lift the Rear Cover from the bottom.

3

4

2

6

5

1

Summary of Contents for KDL-22EX355















































Reviews: