Sony IT-M804 Operating Instructions Manual Download

Page: 66 / 80

Intercom Operation

Paging all phones (ALL PAGE)

You can page all phones connected to the LINE 1 jack through the
speakerphone.

Example

: Page all phones from

station number 02.

Pick up the handset.

Press

(ALL PAGE)

“ALL PAGE” appears on the
display of the phone making the
page.

The other phones being called
ring once and
“ALL PAGE 02” appears on
the display.

You can page all phones
through the speakerphone.

When you’re done talking,
replace the handset in the
cradle.

Notes

• When the other phone are busy with intercom, page, or all page, you cannot

execute all page.

• You cannot use All Page for the phone which is on an outside call or in Do

Not Disturb mode.

• Answering or finishing an all page is not available from the paged phone.

Tips

• If you press

(ALL PAGE)

in step 2 without performing step 1, the

speakerphone will automatically turn on. To disconnect the speakerphone
conversation, press

(SPEAKERPHONE)

• When being called with all page, press

(SPEAKERPHONE)

to cancel the

calling and operate the phone.

(SPEAKERPHONE)

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands