Sony IT-M804 Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 80

background image

Intercom Operation

65

US

Intercom Operation

Voice paging (PAGE)

You can page the other phone connected to the LINE 1 jack without
any operation on the other phone. The phone being called rings once
and the speakerphone automatically turns on.

Example

: Page from station

number 02 to 03.

1

Pick up the handset.

2

Press

(PAGE)

.

“PAGE ??” appears on the
display.

3

Enter the two digits station
number (01 to 16) by pressing
the dialing keys.
The phone pages immediately
after the number is entered.
“PAGE TO 03” appears on the
display of the phone making a
call.
The phone rings and “PAGE
FROM 02” appears on the
display of the phone receiving a
call.
You can begin talking.

4

When you’re done talking,
replace the handset in the
cradle.

Notes

• Paging is available between two phones only. If the other phone are busy

with intercom, page, or all page, you will hear a busy tone and “BUSY” will
be displayed.

• If the other phone is in Do Not Disturb mode, you will hear a short busy tone

and “DO NOT DISTURB” will be displayed.

• While conversing with an outside caller via the phone to be paged, you

cannot page that phone. If you press

(PAGE)

, you will hear a busy tone.

• If you enter your station number mistakenly in step 3, you will hear five

short error beeps. If you enter a station number which has not been assigned,
“NO ANSWER” will be displayed.

Tips

• If you press

(PAGE)

in step 2 without performing step 1, the speakerphone

will automatically turn on. To disconnect the speakerphone conversation,
press

(SPEAKERPHONE)

.

• A person can also answer a page by picking up the handset in step 3.

(SPEAKERPHONE)

«
...
63
64
65
66
67
...
»

Summary of Contents for IT-M804

















































































Reviews:

No comments

Related manuals for IT-M804

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 135

TRU341 - TRU 341 Cordless Phone

Brand: Uniden Pages: 20

Brand: Clarity Pages: 2

Brand: Grandstream Networks Pages: 6

Brand: Swisscom Pages: 25

Brand: AT&T Pages: 12

Brand: Scitec Pages: 12

Brand: Uniden Pages: 28

Brand: GE Pages: 97

POLYCOM SOUNDSTATION IP 6000

Brand: Armstrong Pages: 2

Brand: Valcom Pages: 4

Brand: Memorex Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands