2
ICD-CX50
TABLE OF CONTENTS
1.
GENERAL
...................................................................
3
2.
DISASSEMBLY
2-1.
Case (Front) .....................................................................
4
2-2.
Ornamental Belt Block Assy ...........................................
5
2-3.
Case (U) Block Assy .......................................................
5
2-4.
Main Block Assy .............................................................
6
2-5.
MAIN Board, SWITCH Board .......................................
6
2-6.
JACK Board .....................................................................
7
2-7.
Cover (U), Cover (Lcd) ...................................................
7
2-8.
Camera Block Assy .........................................................
8
2-9.
LCD Board, LCD Unit ...................................................
8
3.
TEST MODE
...............................................................
9
4.
DIAGRAMS
4-1.
Block Diagram – MAIN Section-1 – ............................. 12
4-2.
Block Diagram – MAIN Section-2 – ............................. 13
4-3.
Block Diagram – POWER Section – .............................. 14
4-4.
Printed Wiring Board – MAIN Board – ......................... 15
4-5.
Schematic Diagram – MAIN Board (1/6) – ................... 16
4-6.
Schematic Diagram – MAIN Board (2/6) – ................... 17
4-7.
Schematic Diagram – MAIN Board (3/6) – ................... 18
4-8.
Schematic Diagram – MAIN Board (4/6) – ................... 19
4-9.
Schematic Diagram – MAIN Board (5/6) – ................... 20
4-10. Schematic Diagram – MAIN Board (6/6) – ................... 21
4-11. Printed Wiring Board – CAMERA FLEXIBLE Board – 22
4-12. Schematic Diagram – CAMERA FLEXIBLE Board – .. 23
4-13. Printed Wiring Board – LCD Board – ............................ 24
4-14. Schematic Diagram – LCD Board – ............................... 25
4-15. Printed Wiring Board – SWITCH FLEXIBLE Board – . 26
4-16. Schematic Diagram – SWITCH FLEXIBLE Board – ... 27
4-17. Printed Wiring Board – SWITCH Board – .................... 28
4-18. Schematic Diagram – SWITCH Section – ..................... 29
4-19. Printed Wiring Boards – JACK Section – ...................... 30
4-20. Schematic Diagram – JACK Section – ........................... 31
5.
EXPLODED VIEWS
5-1.
Case (Front) Section ........................................................ 35
5-2.
Case (Rear) Section ......................................................... 36
5-3.
Slider Section .................................................................. 37
5-4.
Camera Section ................................................................ 38
5-5.
MAIN Board Section ....................................................... 39
6.
ELECTRICAL PARTS LIST
.................................. 40
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270
°
C
during repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
✩
Replacement of IC1001 used in this set requires a special tool.
•
The voltage and waveform of CSP (chip size package) cannot
be measured, because its lead layout is different from that of
conventional IC.
•
Lead layouts
surface
Lead layout of
conventional IC
CSP (chip size package)
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. Operating instructiondd
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
