6-56
HVR-M10C/M10E/M10J/M10N/M10P/M10U
00
2-2.
INITIALIZATION OF 8, 9, A, B, C, D, 13, 18,
1A, 1B, 1C, 1D PAGE DATA
Note:
When reading or writing the 13, 18, 1A, 1B, 1C, 1D page data,
select page: 0, address: 10, and set data: 01, then select 3, 8, A, B, C
or D page. The 13, 18, 1A, 1B, 1C or 1D page can be chosen by this
data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
2-2-1.
INITIALIZATION OF A, B, D, 1A, 1B PAGE DATA
Note:
When reading or writing the A, B, D page data, select page: 0,
address: 10, and set data: 00.
When reading or writing the 1A or 1B page data, select page: 0,
address: 10, and set data: 01, then select A or B page. The 1A or 1B
page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1. Initializing the A, B, D, 1A, 1B Page Data
Note1:
If the A, B, D, 1A, 1B page data has been initialized, the following
adjustments need to be performed again.
1) Modification of A, B, D, 1A, 1B page data
Adjusting page
A
Adjusting Address
10 to FF
Adjusting page
B
Adjusting Address
00 to FF
Adjusting page
D
Adjusting Address
10 to 7A
Adjusting page
1A
Adjusting Address
00 to FF
Adjusting page
1B
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
7
04
Set the following data.
00 (HVR-M10J/M10U/M10N
(NTSC))
01 (HVR-M10E/M10P/M10C
(PAL))
4
7
01
XX
Set the data. (Note2)
5
7
00
01
Set the data, and press PAUSE
button. (Note2)
6
7
02
Check that the data changes to
“01”
7
Perform “Modification of A, B,
D, 1A, 1B Page Data”.
Note2:
XX=20: Initializing A page
XX=21: Initializing B page
XX=22: Initializing D page
XX=23: Initializing 1A page
XX=24: Initializing 1B page
XX=25: Initializing A and 1A page
XX=26: Initializing B and 1B page
XX=28: Initializing A, B, D, 1A and 1B page
2. Modification of A, B, D, 1A, 1B Page Data
If the A, B, D, 1A, 1B page data has been initialized, change the
data of the “Fixed data-2” address shown in the following tables by
manual input.
Modifying Method:
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
2)
When changing the A, B, D page data, select page: 0, address:
10, and set data: 00.
3)
When changing the 1A, 1B page data, select page: 0, address:
10, and set data: 01.
After completing the modification of 1A, 1B page data, reset
the data of this address to “00”.
4)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
5)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of A, B, D, 1A, 1B Page data
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
2
00
29
Set the data.
3
2
01
29
Set the data, and press PAUSE
button.
Note:
If the following symptoms occur after completing of the
“Modification of A, B, D, 1A, 1B page data”, check that the data of
addresses: 1A to 4F of A page and the data of addresses: 12 to 19 of
D page are same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
3. A Page Table
Note1:
The data of page: 0, address: 10 must be “00”.
Note2:
Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
D, 1A, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
D, 1A, 1B Page Data”.)
Address
Remark
Initial value
Address
Remark
Initial value
00 to 0F
10
11 to 17
18
19 to CF
D0
D1
D2
D3 to D4
D5
D6
D7
D8
D9
DA to FF
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Table. 6-2-2.
Summary of Contents for HVR-M10C
