Sony HT-SF370 Operating Instructions Manual Download

Page: 71 / 76

Ad
dit
ion
al I

rmatio

Tuner

The FM reception is poor.

• Use a 75-ohm coaxial cable (not supplied)

to connect the receiver to an outdoor FM
antenna as shown below. If you connect
the receiver to an outdoor antenna, ground
it against lightning. To prevent a gas
explosion, do not connect the ground wire
to a gas pipe.

Radio stations cannot be tuned in.

• Check that the antennas are connected

securely. Adjust the antennas and connect
an external antenna, if necessary.

• The signal strength of the stations is too

weak (when tuning in with automatic
tuning). Change to monaural reception
(page 35).

• No stations have been preset or the preset

stations have been cleared (when tuning
by scanning preset stations). Preset the
stations (page 37).

Remote commander

The remote does not function.

• Point the remote at the remote sensor on

the receiver.

• Remove any obstacles in the path between

the remote and the receiver.

• Replace all the batteries in the remote with

new ones, if they are weak.

• Make sure you select the correct input on

the remote.

Others

The POWER/ACTIVE STANDBY
indicator is flashing.

• The receiver is in protection mode. Turn

off the receiver and turn it on again.

The receiver is turned off
automatically.

• The AUTO STBY function is working

(page 62).

ANTENNA

Receiver

To ground

Ground wire
(not supplied)

Outdoor FM antenna

continued

Summary of Contents for HT-SF370













































































Search results

Summary of Contents for HT-SF370

Reviews:

Related manuals for HT-SF370

Brands by name

Popular brands

Sony HT-SF370, Operating Instructions Manual

Search results

Summary of Contents for HT-SF370

Reviews:

Related manuals for HT-SF370

Brands by name

Popular brands