background image

HT-S20R

4

Sony CONFIDENTIAL

For Authorized Servicer

SECTION  1

SERVICING  NOTES

The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.

UNLEADED  SOLDER

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(

Caution:

 Some printed circuit boards may not come printed with 

the lead free mark)

 : LEAD  FREE  MARK

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher than 

ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.

Caution:

  The printed pattern (copper foil) may peel away if the 

heated tip is applied for too long, so be careful!

• Strong 

viscosity

 

Unleaded solder is more viscous (sticky, less prone to 

fl

 ow) than 

ordinary solder so use caution not to let solder bridges occur 
such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

NOTE  OF  REPLACING  THE  FUSE

The fuse is or could be in the neutral. When a fuse is being replaced, 
the main plug shall be disconnected from the AC outlet to prevent 
electric shock.

ADVANCE  PREPARATION  WHEN  CONFIRMING  OPER-
ATION

All of the units included in the HT-S20R (SA-WS20R/SS-S20R/
SS20R/Remote control) are required to con

fi

 rming operation of this 

unit. Check in advance that you have all of the units and accessories.

DISCHARGE  PROCESSING  METHOD

When disassembling the SA-WA20R (active subwoofer) after check-
ing the operation of this unit, for the electric shock prevention, per-
form the discharge processing by connecting the resistor at both ends 
of the speci

fi

 ed capacitor with referring to the 

fi

 gure below.

Note:

 Be sure to discharge using a resistor of 800 

 or higher.

– POWER Board (Conductor Side) –

800 

:

/2 W

(for C904)

800 

:

/2 W

(for C931)

800 

:

/2 W

(for C933)

ABOUT  THE  PROTECTION

[PROTECT] appears in the front panel 
display of the subwoofer, the sound is 
muted, and buttons on the remote control 
or subwoofer other than 

Æ

 (power) do not 

work.

• The protection feature is activated. 

Press 

Æ

 (power) to turn the system off and 

disconnect the AC power cord (mains lead) and 
check the items below.

 

— Make sure that the ventilations of the 

subwoofer are not covered and turn on the 
system after a while.

 

— When the system is using the USB connection, 

remove the USB device and turn on the 
system. If the system operates properly, the 
current of the connected USB device is over 
the maximum output current of the system 
500 mA, or the USB device may have an 
abnormality.

NOTE  OF  PERFORMING  THE  OPERATION  CHECK  IN  THE  
STATE  THAT  HEATSINK  IS  REMOVED

When performing the operation check in the state that this unit is 
disassembled, it is possible to perform the operation check in the 
state that heatsink is removed from MAIN board. However, in that 
case, set the volume to low level and perform the work in the short 
time so as a few minutes.
When it is necessary to work in the middle level volume or more or 
a few minutes or more, be sure to perform in the state that heatsink 
is installed to the MAIN board.

– MAIN Board (Component Side) –

heatsink

RESET  METHOD

Press MENU to turn on the menu in the front 
panel display.

Press 

j

/

„

 to select [RESET], then press ENTER. 

Press 

j

/

„

 to select [ALL RESET], then press 

ENTER. 

Press 

j

/

„

 to select [START], then press ENTER. 

All the settings return to their initial status. 

To cancel resetting

Select [CANCEL] in step 4.

Ver. 1.1

SYS SET

2021/02/10 22:25:21 (GMT+09:00)

Summary of Contents for HT-S20R














































Reviews: