background image

SERVICE MANUAL

Sony Corporation

Published by Sony Techno Create Corporation

HT-GT1

SA-WGT1

SPECIFICATIONS

HT-GT1

SOUND BAR

SA-WGT1

ACTIVE SUBWOOFER

9-896-032-03

2015A33-1

© 

2015.01

US Model

AEP Model

UK Model

E Model

Australian Model

Ver. 1.2  2015.01

•  All of the units included in the HT-GT1 (SA-WGT1/SS-GT1) 

are required to confi rming operation of SA-WGT1. Check in 
advance that you have all of the units.

COMPONENT  MODEL  NAME

HT-GT1

Bar Speaker (Speaker System)

SS-GT1

Subwoofer (Active Subwoofer)

SA-WGT1

Speaker section

Speaker system:

Subwoofer, Bass reflex

Speaker unit:

180 mm (7 

1

/

8

 in), cone type 

Rated impedance:

4 ohms

Inputs

AUDIO IN/PARTY CHAIN IN L/R:

Voltage 0.8 V, impedance 
47 

kilohms

OPT IN:

Supported audio signal: 
2-channel Linear PCM

Outputs

AUDIO OUT/PARTY CHAIN OUT L/R:

Voltage 2 V, impedance 1 kilohm

Tuner section

FM stereo, FM superheterodyne tuner
Antenna:

FM lead antenna

Tuning range:

BLUETOOTH section

Communication system:

BLUETOOTH Standard version 3.0

Output:

BLUETOOTH Standard Power 
Class 2

Maximum communication range:

Line of sight approx. 10 m 

1)

Frequency band:

2.4 GHz band (2.4000 GHz – 

Modulation method:

FHSS (Freq Hopping Spread 
Spectrum)

Compatible BLUETOOTH profiles

2)

:

A2DP (Advanced Audio 
Distribution Profile)
AVRCP 1.3 (Audio Video Remote 
Control Profile)

Supported codecs:

SBC (Sub Band Codec)
AAC (Advanced Audio Coding)

1)

 The actual r ange will vary depending 

on  factors such as obstacles between 
devices, magnetic fields around a 
microwave oven, static electricity, 
reception sensitivity, antenna’s 
performance, operating system, 
software application, etc.

2)

 BL UETOOTH standard profiles 

indicate the purpose of BLUETOOTH 
communication between devices.

USB section

Supported format:

MP3 (MPEG 1 Audio Layer-3):
32 kbps – 320 kbps, VBR
WMA:
48 kbps – 192 kbps
AAC:
48 kbps – 320 kbps
WAV:
16 bit PCM

Sampling frequencies:

MP3 (MPEG 1 Audio Layer-3):
32 kHz/44.1 kHz/48 kHz
WMA:
32 kHz/44.1 kHz/48 kHz
AAC:
32 kHz/44.1 kHz/48 kHz
WAV:
8 kHz – 48 kHz

Supported USB device:

Mass Storage Class

Maximum current:

1 A

 (USB) port:

Type A

General

Power requirements:

Power consumption:

70 W

Power consumption (at the Power 
Saving mode):

European model:

mode is set to off)

mode is set to on)
Other models:

Active subwoofer:
290 mm × 420 mm × 275 mm 

0.5 W

Speaker system:
800 mm × 110 mm × 102 mm 

Mass (Approx.):

Active subwoofer:
7.1 kg (15 lb 10 

1

/

2

 oz) 

Speaker system:
2.8 kg (6 lb 2 

3

/

4

 oz) 

Quantity:

Active subwoofer:
1 piece
Speaker system:
1 piece

Supplied accessories

Optical digital cable (1)
Remote control (1)
R03 (Size AAA) batteries (2)
FM lead antenna (1)

Design and specifications are subject 
to change without notice.

Amplifier section

U.S. model:
POWER OUTPUT AND TOTAL 
HARMONIC DISTORTION (FTC output 
power):

Front L/F ront R:
With 3 ohms  loads, both channels 
driven, from 400  – 10,000  Hz;  
rated 32 watts per channel 
minimum RMS powe r, with no 
more than 1.0% total harmonic 
distortion from  250  milliwatts to 
rated output.

Output power (reference):

Front L/F ront R:
40  W  + 40  W  (per channel at 3 
ohms,  1 kHz)
Subwoof er:
180 W  (at  4  ohms,   100 Hz)

Brazilian model:
Total RMS  output power:

200 W

Front L/F ront R:

RMS output power:
80 W (40 W per channel × 2, at 
3 ohms,  1 kHz, 10% THD*)

Subwoof er:

RMS output power:
120 W (at 4 ohms,  100 Hz, 10% 
THD*)

Other models:
Power output (rated):

Front L/F ront R:
32 W  + 32 W  (at 3 ohms,  1 kHz, 1% 
THD*)

Power output (reference):

Front L/F ront R:
40  W  + 40  W  (per channel at 
3 ohms,  1 kHz)
Subwoof er:
180 W  (at  4  ohms,   100 Hz)

* Total Harmonic Distortion

USA and Brazilian models:  
87.5 MHz - 108.0  MHz (100 kHz 
step)
Other models:  
87.5 MHz - 108.0  MHz (50 kHz 
step)

USA and Mexican models:
AC 120 V, 60  Hz
Latin American model  (except for 
Bolivian, Chilean, Argentine, and 

 

Mexican models):
AC 110 V – 240 V, 50/60  Hz
Saudi Arabian,African and Irarian
models:
AC 120 V – 240 V, 50/60  Hz
Other models:
AC 220 V – 240 V, 50/60  Hz

(11 

3

/

8

 in × 16 

1

/

2

 in × 10 

7

/

8

 in )

(31 

1

/

2

 in × 4 

3

/

8

 in × 4 in )

0.5 W (When BLUETOOTH standby   

6 W (When BLUETOOTH standby   

(33

 

feet) 

2.4835

 GHz)

 

Dimensions (W/H/D) (Approx.):

Note:

Be sure to keep your PC used for service and 
checking of this unit always updated with the 
latest version of your anti-virus software.
In case a virus affected unit was found during 
service, contact your Service Headquarters. 

•  Please refer to service manual separately issued for Bar 

Speaker.

Summary of Contents for HT-GT1









































































Reviews: