Cha
p
te
r 7
SR Mot
ion
(Wi
th
HKS
R
-10
2
In
s
talle
d)
88
7-2 Select FPS Function
operation that is comparable to docked operation.
However, some limitations apply to the available formats.
For details, see the next section “Formats available for
Select FPS shooting”.
Formats available for Select FPS shooting
Note
The 4:4:4 format is not available when the scan method is
progressive and the target frame frequency is 50 Hz or
higher.
a
: Available for separate operation by optical-fiber
connection
*
: Not available for separate operation by optical-fiber
connection
z
: Not available for docked operation
s
:Available when the HKSR-103 is installed (docked
operation)
To dub tapes shot with Select FPS using
two units
Instead of connecting this unit to a camera, connect two
units, and set Select FPS to “DUB”.
Note
When the HKSR-102 is not installed, or when the unit is
connected to the camera by a BNC cable (in separate
operation), the operation is the same as “DUB”, even if
“SELECT FPS” is set to “ON”.
7-2-3 Using the Ramp Function
The Ramp function allows you to achieve speed variations
by changing the number of frames shot (FPS) during
Select FPS recording.
There are two Ramp modes: manual mode, in which you
specify upper and lower limits and manually vary the
speed within that range, and auto mode, in which you
specify start and end frames and a duration, and allow the
unit to vary the speed automatically according to preset
rules.
Proceed as follows to set up the Ramp function.
1
In the SYSTEM Setup menu, select EDIT >RAMP.
A setting window opens.
2
Select the Ramp function operating mode from the
following.
Auto(Linear):
Varies the number of frames shot
(FPS) linearly.
Auto(Inverse):
Varies the inverse of the number of
frames shot (frm) linearly.
Auto(Even):
Varies the number of frames shot so that
there are the same number of frames for each
frequency.
Auto(User):
Varies the number of frames shot along a
user-specified curve.
Manual:
Varies the number of frames shot manually
within preset upper and lower limits.
Off:
Varies the number of frames shot manually with
no range limits.
3
Make the settings required by the selected mode.
Select FPS
setting
FRAME
(target
frame
frequency)
SIGNAL (signal format)
FPS
FORMAT
(system
frame
frequency)
4:2:2
(YCbCr)
4:4:4 SQ
(RGB)
4:4:4 HQ
(RGB)
On 23.98
23.98
a
a
a
24
24
a
a
a
25
24
a
a
a
25
a
a
a
29.97
23.98
a
a
a
29.97
a
a
a
30
24
a
a
a
25
a
a
a
50
24
a
*
s
*
z
25
a
*
s
*
z
50
a
*
z
*
z
59.94
23.98
a
*
s
*
z
29.97
a
*
s
*
z
59.94
a
*
z
*
z
60
24
a
*
s
*
z
25
a
*
s
*
z
50
a
*
z
*
z
Off
23.98
a
a
a
24
a
a
a
25
a
a
a
29.97
a
a
a
50
a
*
z
*
z
59.94
a
(F23
only)
*
z
*
z
Edit Config
RAMP
Auto Spd1
Auto Spd2
MANU
1
20
Duration
Load Curve
5s
Manu Spd1
1
S y s t e m S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEY MAP
KEY INHI
REMOTE/LCKAL
SERVO
REC INHI
EDIT
POWER
BATTERY
OTHERS
OFF
MAP
LCL
SRW-1
TCR
00:00:00:00
C A S S O U T
Summary of Contents for HKSR-101
Page 126: ...Index 126 Index ...
