21
Audio Functions
Cha
p
te
r 2
Loc
a
tio
ns
a
nd F
unc
tions
of
P
a
rts
a
nd Cont
rol
s
k
AUDIO IN CH-1/CH-2 / CH-3/CH-4 (audio input
selection) switches
CH-1/CH-2 switches
Select the audio input signals to be recorded on audio
channels 1 and 2.
FRONT:
The input signal source is the microphone
connected to the MIC IN connector.
REAR:
The input signal source is the audio equipment
connected to the AUDIO IN CH1/CH2 connectors.
WIRELESS:
The input signal source is an optional WRR-
855A/855B UHF Synthesized Tuner Unit.
CH-3/CH-4 switches
Select the audio input signals to be recorded on audio
channels 3 and 4.
F (front):
The input signal source is the microphone
connected to the MIC IN connector.
R (rear):
The input signal source is the audio equipment
connected to the AUDIO IN CH1/CH2 connectors.
W (wireless):
The input signal source is an optional WRR-
855A/855B UHF Synthesized Tuner Unit.
l
CUE IN (cue track input) switch
Selects the input signal to be recorded on the cue track.
CH-1:
Signal selected by the AUDIO IN CH-1 switch
MIX:
Mixed signals selected by the AUDIO IN CH-1 and
CH-2 switches
CH-2:
Signal selected by the AUDIO IN CH-2 switch
When recording mixed signals by setting this switch to
MIX, be sure to confirm that the emphasis settings of the
two channels (on/off) are the same. If they are different, the
camcorder cannot record or play back mixed signals
correctly.
When the AES/EBU format audio signal is selected, the
emphasis settings are determined by the channel status of
the AES/EBU format audio signal (emphasis bit).
When an audio signal other than the AES/EBU format
audio signal is selected, the emphasis setting depends on
the setting of AU REC EMPHASIS
on the
AUDIO-2 page of the MAINTENANCE menu.
m
LINE / AES/EBU / MIC selectors
Select the audio source of the audio input signals input to
the AUDIO IN CH1/CH2 connectors.
LINE:
Line input audio equipment
AES/EBU:
AES/EBU format audio signal
MIC:
Microphone input
If this selector is set to the MIC position and the +48V/
OFF switch is set to +48V, and if you inadvertently connect
any audio device other than a microphone to the AUDIO
IN CH1/CH2 connectors, the device may be damaged.
n
+48V/OFF switches
Select either of the following positions for the
microphones to be connected.
+48V:
For a microphone to use an external power supply
OFF:
For a microphone to use an internal power supply
o
AUDIO OUT (audio output) connector (XLR type,
5-pin, male)
Outputs the audio signals recorded on audio channels 1
and 2 or audio channels 3 and 4.
The MONITOR switch and CH-1/2 / CH-3/4 switches
allow you to select the audio signal to be monitored.
When this connector is not being used, attach the supplied
XLR connector cover onto it.
p
AUDIO IN CH1/CH2 (audio channel-1 and
channel-2 input) connectors (XLR type, 3-pin, female)
These are audio input connectors for channels 1 and 2 to
which you can connect audio equipment or a microphone.
When the LINE / AES/EBU / MIC selector is set to AES/
EBU, the CH1 connector is used for channel-1 and -2
inputs, and the CH2 connector, for channel-3 and -4 inputs.
When the connector is not being used, attach the supplied
XLR connector cover onto it.
q
DC OUT 12 V (DC power output) connector (4-pin,
female)
Supplies power for an optional WRR-861A/861B/862A/
862B UHF Portable Tuner. Do not connect any equipment
other than the UHF portable tuner.
Note
Note
