7
j
AUDIO IN 1 and 2 connectors (XLR 3-pin)
To input microphone or line signals.
k
DC IN connector (4-pin)
Connect to a DC power source (10.5 V to 17 V) when using the
camera as a standalone unit.
Note
In standalone status, power supply from this unit is limited to
6.5 A. Check the power consumption of the device to be
connected.
l
CCU (camera control unit) connector (electro-optical
multi-connector)
Connect to the CAMERA connector of the HDCU2000/2500
Camera Control Unit using an electro-optical composite cable.
Power, video, audio, and control signals are passed between
the camera and HDCU2000/2500 using just one cable.
m
SDI 1 (serial digital interface 1) connector (BNC type)
For 3G-SDI, HD-SDI or HD PROMPTER signal output.
Note
HD PROMPTER signal output only when <CAM MODE> is set
to 4K/HDR MODE. Set <CAM MODE> to NORMAL as
necessary.
For details on output signals, see “Setting the Camera
Outputs” (page 19).
n
SDI 2 (serial digital interface 2) connector (BNC type)
For HD-SDI signal output or HD TRUNK signal input. During
stand-alone operation, also used for inputting an HD-SDI
return signal. When RET (return) is set to 1, this is displayed
in the viewfinder.
Note
This connector is disabled when <CAM MODE> is set to 4K/
HDR MODE. Set <CAM MODE> to NORMAL as necessary.
For details on the output signals, see “Setting the Camera
Outputs” (page 19).
o
SDI-MONI (serial digital interface) connector (BNC-
type)
To output HD-SDI or SD-SDI signals.
For details on the output signals, see “Setting the Camera
Outputs” (page 19).
p
TEST OUT (test signal output) connector (BNC type)
To output analog signals.
This also supplies the VBS signal, an HD signal nearly equal
to the signal output from the VF connector, an HD-SYNC
signal, or an SD-SYNC signal depending on which of these
you have selected on the menu.
For details on the output signals, see “Setting the Camera
Outputs” (page 19).
q
NETWORK TRUNK connector (RJ-48 8-pin)
Connects a device connected to the CCU’s NETWORK
TRUNK connector to the network.
r
PROMPTER 1 connector (BNC type)
To output the signal input from the camera control unit’s
PROMPTER INPUT connector. If the connected camera
control unit has two prompter inputs, a signal of prompter 1 is
output. In standalone status, this is used for GENLOCK input.
s
PROMPTER 2 connector (BNC type)
To output the signal input from the camera control unit’s
PROMPTER 2 INPUT connector. This is enabled only for the
unit which has the PROMPTER 2 input. In standalone status,
this is used for VBS RET input.
t
REMOTE connector (8-pin)
To connect the camera to an optional MSU-1000/1500 Master
Setup Unit, RCP-1000/1500-series Remote Control Panel, or
RM-series Remote Control Unit via a CCA cable. The
connected unit may then control the camera.
Note
When the camera is connected to a CCU, do not connect any
device to this connector.
u
CRANE connector (12-pin)
For external interface with a viewfinder or external data.
v
TRACKER connector (10-pin)
For communication between the camera operator and the
tracker, and also for intercom channels 1 and 2. It also
supplies the up tally signal and the program audio signal.
w
RET (return video) CONTROL connector (6-pin)
To connect a CAC-6 Return Video Selector.
x
DC OUT connector (4-pin)
To supply power to a script light of the BKP-7911 Script
Holder.
y
Accessory bracket
To secure optional accessories such as the BKP-7911 Script
Holder.
For more information on attaching an accessory, see the
accessory’s operation manual.
