61
HCD-IS10
MAIN BOARD IC101 M30620MCP-A18FPU0 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
SYS_RXD
O
Serial data output to the SYSTEM CONTROL connector (SA-WSIS10)
2
SYS_CLK
O
Serial data transfer clock signal output to the SYSTEM CONTROL connector (SA-WSIS10)
3
CEC_RX_IN
I
CEC serial data input from the HDMI OUT connector
4
SIRCS_IN
I
SIRCS signal input from the remote control receiver
5
CODEC_DO
O
Serial data output to the A/D converter
6
CODEC_DI
I
Serial data input from the A/D converter
7
CODEC_CLK
O
Serial data transfer clock signal output to the A/D converter
8
BYTE
I
External data bus width selection signal input terminal Fixed at "L" in this set
9
CNVss
I
Processor mode switch input terminal (for test)
10
CODEC_PDN
O
Reset signal output to the A/D converter "L": reset
11
CODEC_CS
O
Chip select signal output to the A/D converter
12
RESET
I
System reset signal input from the SYSTEM CONTROL connector (SA-WSIS10) "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
13
Xout
O
Main system clock output terminal (10 MHz)
14
Vss
-
Ground terminal
15
Xin
I
Main system clock input terminal (10 MHz)
16
Vcc1
-
Power supply terminal (+3.3V)
17
NMI
I
Non-maskable interrupt input terminal Fixed at "H" in this set
18
CODEC_INT
I
Interrupt signal input from the A/D converter
19 to 21
-
-
Not used
22
CEC_TX_OUT
O
CEC serial data output to the HDMI OUT connector
23
VIDEO_MUTE 0
O
Video signal input selection signal output terminal
24
BACKLIGHT_
LED1
O
LED drive signal output terminal
25
V_SEL
O
Video signal input selection signal output terminal
26
BACKLIGHT_
LED2
O
LED drive signal output terminal
27
DMPORT_DET
I
Connect detection signal input from the DMPORT jack
28
VIDEO_MUTE1
O
Video signal input selection signal output terminal
29
I2C_CLK
I/O
Two-way I2C clock bus terminal Not used
Two-way I2C data bus terminal Not used
Serial data output to the DMPORT connector
I
Serial data input from the DMPORT connector
-
Not used
-
Not used
Serial data output to the servo DSP
I
Serial data input from the servo DSP
I
Serial data transfer clock signal input from the servo DSP
System wake up signal output to the SYSTEM CONTROL connector (SA-WSIS10)
39, 40
-
-
Not used
41
EPM
I
Not used
42, 43
-
-
Not used
44
P_CONT1
O
Power on/off control signal output terminal "H": power on
45
P_CONT_TS
O
Power on/off control signal output terminal for the touch sensor "H": power on
46
FLASH_CE
-
Not used
47
P_CONT_FL
O
Power on/off control signal output terminal for the front panel section "H": power on
48
EJECT_KEY
I
Front panel key input terminal for the eject (A/D input)
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
