28
Chapter 1
Overview
Chap
te
r 1
O
v
e
rv
ie
w
Displaying Various Data
The unit detects the audio mode as follows:
In the playback mode:
Detects the audio mode
recorded on the tape.
In the recording/EE mode:
Detects the selected
audio mode in [AUDIO MODE] of the [AUDIO
SET] menu.
When the INPUT SELECT switch is set to HDV/
DV and HDV or DV signals are being input:
Detects the audio mode of the signals being input.
(The setting of [AUDIO MODE] in the [AUDIO
SET] menu becomes invalid.)
Audio mode: 2-channel (48 kHz, 16 bits in DV mode)
(The levels of two channels, channels 1 and 2, are displayed.)
Audio mode: 4-channel (32 kHz, 12 bits in DV mode)
(The levels of four channels, channels 1 to 4, are displayed.
When the unit is in the audio dubbing mode, the levels of
playback sound are displayed on CH1 and CH2. The levels of
input sound to be dubbed are displayed on CH3 and CH4. To
check only the sound to be dubbed before dubbing, press the
AUDIO DUB button while the unit is in the stop mode. Only
the level meters of the channels to be dubbed (channels 3 and
4) fluctuate.
In EE, recording, or audio dubbing (only the channels
used to dub) mode, if the input levels exceed 0 dB,
portions of the meters turn red.
During playback, while signals are input via the HDV/
DV jack, or when the AUDIO INPUT switch is set to
AUTO, the level meters do not turn red.
Link symbol
When the AGC (Auto Gain Control) of a pair of
channels is linked, this symbol is placed between the
channels.
In the EE mode, if [AGC CH1,2] in the [AUDIO SET]
menu is set to [LINKED] and the AUDIO INPUT
switch is set to AUTO, channels 1 and 2 can be linked
for AGC operation and for stereo sound where channel
1 is set for the left sound and channel 2 is set for the right
sound.
In the EE mode, when [AGC CH3,4] in the [AUDIO
SET] menu is set to [LINKED] and the AUDIO INPUT
switch is set to AUTO, channels 3 and 4 can be linked
for AGC operation and for stereo sound where channel
3 is set for the left sound and channel 4 is set for the right
sound.
When the INPUT SELECT switch is set to HDV/DV,
the AGC does not function and channels are not linked.
Also, link symbols do not appear.
OUTPUT screen
The OUTPUT screen is displayed when STATUS
CHECK screen is set to [OUTPUT].
You can confirm the following setting values:
– [HDV/DV SEL] in the [IN/OUT REC] menu
– [SDI/CMPNT], [DOWN CONVERT] and [DV
WIDE CONV] of [VIDEO OUT] in the [IN/OUT
REC] menu
– [HDV
t
DV CONV], [DOWN CONVERT] and
[DOWN CONV AU] of [i.LINK SET] in the [IN/
OUT REC] menu
For details on OUTPUT settings, see “IN/OUT REC menu”
on page 72.
Note
Link symbol
Note
OUTPUT
2/5
HDV/DV
S
EL :
AUTO
VIDEO OUT
S
DI/CMPNT :
10
8
0i / 4
8
0i
DOWN CONVERT:
S
QUEEZE
DV WIDE CONV:
S
QUEEZE
[
S
TATU
S
CHECK
]
:
END
OUTPUT
3
/5
[
S
TATU
S
CHECK
]
:
END
i.LINK
S
ET
HDV DV CONV: OFF
DOWN CONVERT:
S
QUEEZE
DOWN CONV AU: CH1,CH2
