Sony Cyber-shot DSC-HX10 Service Manual Download Page 28

Page: 28 / 28

DSC-HX10/HX10V_L2

3-1E

3. ASSEMBLY

Assembly-1:

Attaching Method of LCD Cushion (330), LCD

Window (330).

Attach the LCD Cushion (330).

Peel off the released paper.

Set the LCD to the Cabinet (Rear) Assy.

Align shape of corner.

LCD

Released Paper

LCD

Cushion

(330)

LCD

Cabinet (Rear) Assy

Install the LCD Window (330).

Remove the LCD.

Blow the air before attaching.
Be sure to keep away from dust.

LCD

Cabinet (rear) assy

LCD Window (330)

Assembly-2:

Precaution During of attachment Shield Ring.

Shield Ring

Glossy surface

Cabinet Front

Precaution During of attachment
Shield Ring.

Assembly-3:

Precaution During of Main Frame installation.

Main Frame

Between the Front Cabinet
and the BT Frame.

Inside the Front Cabinet
and the BT Frame.

Assembly-4:

Precaution During of Rotary Plate installation.

Marking

Rotary plate

Cabinet (Upper) Assy

Non Click

After installation, turn the dial to confirm that there is

no click in the area shown in the figure below.

Adjust the position

(Adjust the position)

RL-127 Board

Assembly-5:

Precaution During of flexible board of the strobe

unit installation.

Boss

Lever

Flexible board of
the strobe unit

Route the Flexible board of the strobe unit as shown in the figure.

Set the Lever as shown in the figure.

Flexible board of
the strobe unit

Lever

Summary of Contents for Cyber-shot DSC-HX10





























Search results

Summary of Contents for Cyber-shot DSC-HX10

Reviews:

Related manuals for Cyber-shot DSC-HX10

Brands by name

Popular brands

Sony Cyber-shot DSC-HX10, Service Manual

Search results

Summary of Contents for Cyber-shot DSC-HX10

Reviews:

Related manuals for Cyber-shot DSC-HX10

Brands by name

Popular brands