19
Error displays/Messages
Automatic tuning is not possible.
• Setting of the local seek mode is not correct.
t
Tuning stops too frequently:
Set “LOCAL-ON” (page 11).
t
Tuning does not stop at a station:
Set “MONO-ON” (page 11).
• The broadcast signal is too weak.
t
Perform manual tuning.
During FM reception, the “ST” indication
flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
t
Set “MONO-ON” (page 11).
An FM program broadcast in stereo is heard in
monaural.
The unit is in monaural reception mode.
t
Set “MONO-OFF” (page 11).
USB playback
You cannot play back items via a USB HUB.
This unit cannot recognize USB devices via a USB
HUB, and is not compatible with a device that has a
HUB function.
Cannot play back items.
• Play back music files are protected by Digital Rights
Management (DRM) technology (page 14).
• Play back items on non-Mass Storage Class USB
devices only.
• If a USB device does not work, reconnect it.
A beep sounds.
During playback, the USB device has been
disconnected.
t
Before disconnecting a USB device, make sure to
stop playback first for data protection.
The sound is intermittent.
The sound may be intermittent at a high-bit-rate of
more than 320 kbps.
BLANK
*
1
Tracks have not been recorded on the MD.
*
2
t
Play an MD with recorded tracks.
CHECKING
The unit is confirming the connection of a USB device.
t
Wait until confirming the connection is finished.
ERROR
*
1
• The disc is dirty or inserted upside down.
*
2
t
Clean or insert the disc correctly.
• A blank disc has been inserted.
• The disc cannot play due to a problem.
t
Insert another disc.
• USB device was not automatically recognized.
t
Reconnect it again.
• Press
Z
to remove the disc.
FAILURE
The connection of speakers/amplifiers is incorrect.
t
See the installation guide manual of this model to
check the connection.
HUB NO SUPRT
USB HUB or devices that have a HUB function are not
supported on this unit.
LOAD
The changer is loading the disc.
t
Wait until loading is complete.
L. SEEK +/–
The local seek mode is on during automatic tuning.
NO DEV
(No Device)
(SOURCE)
is selected without a USB device
connected. A USB device or a USB cable has been
disconnected during playback.
t
Be sure to connect a USB device and USB cable.
NO DISC
The disc is not inserted in the CD/MD changer.
t
Insert discs in the changer.
NO INFO
Text information is not written in the MP3/WMA/
AAC files or ATRAC CD.
NO MAG
The disc magazine is not inserted in the CD changer.
t
Insert the magazine in the changer.
NO MUSIC
The disc/USB device does not a music file.
t
Insert a music CD in this unit or MP3 playable
changer.
t
Connect a USB device with a music file in it.
NO NAME
A disc/album/group/track name is not written in the
track.
NOT READ
The disc information has not been read by the unit.
t
Load the disc, then select it on the list.
NOTREADY
The lid of the MD changer is open or the MDs are not
inserted properly.
t
Close the lid or insert the MDs properly.
OFFSET
There may be an internal malfunction.
t
Check the connection. If the error indication
remains on in the display, consult your nearest
Sony dealer.
OVERLOAD
USB device is overloaded.
t
Disconnect the USB device, then change the source
by pressing
(SOURCE)
.
t
Indicates that the USB device is out of order, or an
unsupported device is connected.
READ
The unit is reading all track and group/album
information on the disc/USB device.
t
Wait until reading is complete and playback starts
automatically. Depending on the disc/USB device
structure, it may take more than a minute.
continue to next page
t
