Sony BVP-550, Maintenance Manual

Page: 921 / 924

3-15(E)
BVP-550
Page Ver. Item Settings Contents
OTHERS 1 FILTER,
[ON]
, OFF ON : A total of 8 settings of the white balance value can be saved
WHT MEM in conbination with the CC filter and WHITE BAL switch settings.
OFF : One white balance value can be saved for the WHITE BAL
switch setting A or B, for a total of 2 settings.
NTSC ENC
[WIDE]
, NRW Sets the band width of the Q signal for the NTSC color encoder.
ROTARY
[STD]
, RVS Selects the mode of MENU SEL switch (as turned counterclockwise
when viewed from the front.)
STD : Cursor moves downwards and a numeric value increases.
RVS : Cursor moves upwards and a numeric value decreases.
OWN CALL R, F&R , OFF Selects whether one or two TALLY lamps are lit corresponding to the
CALL button of camera adaptor pressed, or not. Or selects which
TALLY lamp is lit when the CALL button is pressed.
(This setting is valid in connection with CCU. When the camera is used
alone and MSU/RCP is not connected to the camera, it is always set to
OFF.)
R
: Rear TALLY lamp is lit.
F&R : Rear and front TALLY lamps are lit.
OFF : No TALLY lamp is lit corresponding to the CALL button.
CENTER H POS –20 to 20 (
[XX]
) Shifts horizontally the location of the center marker on the screen.
20 (right)
↔
–20 (left)
CENTER V POS –20 to 20 (
[XX]
) Shifts vertically the location of the center marker on the screen.
20 (up)
↔
–20 (down)
LENS VTR S/S TALK,
[RET2]
Selects the mode of VTR S/S SW of the lens and camera.
TALK : VTR S/S SW of lens functions as INCOM TALK SW
(momentary) and that of the camra as RET2 SW.
RET2 : VTR S/S SW of lens functions as RET2 SW and that of the
camera as INCOM TALK SW.
VF ? DISPLAY
[ON]
, OFF Turns on and off the indication of ? mark at the top-right of the VF screen
with the DISP switch set to ON when the self-diagnosis result is NG (no
good) and so on.
PinP RET RVS
[RVS1]
, RVS 2, OFF Selects the indication mode of VF display in PinP mode. (Does not function
in the unit.)
OTHERS 2 F TALLY RVS
[ON]
, OFF Selects the operation mode of TALLY lamps corresponding to a CALL
button of MSU or RCP pressed when a TALLY signal is input to the camera
from CCU or VTR.
ON
: Rear and front TALLY lamps go out.
OFF : Rear TALLY lamp alone goes out.
1.07 BLK GAM
[ON]
, OFF ON : Inhibits the black gamma adjustment and on/off function from the
INHIBIT MSU or Paint manu.
OFF : Enables the above operation.
1.10 CHAR CAM No.
[1,2,3]
, A,B,C Selects the indication mode of the camera number set by the CAMERA
No. page of Operation menu.
1,2,3 : Indicates in numerics.
A,B,C : Indicates camera numbers 1 to 27 in alphabetical order of A to Z.
(When connecting 28 or more cameras, select “1,2,3”.)
1.10 WHT SETUP
[AWB]
, LEVEL AWB : After executing the LEVEL AUTO, white balance adjustment
MODE data returns to the value before execution.
LEVEL: After executing the LEVEL AUTO, white balance adjustment
data changes to the value after the white balance is adjusted
using TEST 2 signal.
1.10 AW SHADING
[RGB]
, RB ONLY RGB : When automatically adjusting the white balance, R, G, and
MODE B signal waveforms are all flattened.
RB ONLY : When automatically adjusting the white balance, R and B
signal waveforms are flattened.
3-1. Setup Menu
3-1-6. System Config Menu