manualshive.com logo in svg

Sonnen sonnenBatterie 10, Installation Instructions Manual, Page: 81 / 100

Share
Download
Sonnen sonnenBatterie 10 Installation Instructions Manual Download Page 81

Commissioning | 11

KD-557 | 1000241 | EN | 02

81 / 100

11.2.2 Filling in the commissioning report

„

Complete the commissioning report in the appendix of the document in full.

„

Make a copy of the filled in commissioning report, the original remains with the oper-
ator.

„

Send a scan of the commissioning report to the following e-mail address within 5 work-
ing days: 

[email protected]

11.2.3 Taking photos to document installation

The photo upload is obligatory for both offline commissioning and online com-
missioning.

To fully document the installation, photos of the finished installation must be taken and
send to sonnen.

1.

Take the described photos of the storage system (see Installation photos [P. 92]).

2. Go to the following website: 

sonnensupportaustralia.com.au

3. Navigate to Reference > System Commissioning.

4. There the photos can be uploaded, using the procedure described.

5.

Alternatively

 the photos can be send to the following e-mail address: 

[email protected]

Summary of Contents for sonnenBatterie 10





































































































Reviews:

No comments