SONIX SN32F280 Series User Manual Download

Page: 65 / 268

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 65

Version 1.1

1: Enable. (The noise on IC VDD 5V domain detected by NDT5V IP will
trigger.NDT interrupt IRQ0)

Reserved

3.3.12 Noise Detect Status register (SYS0_NDTSTS)

Address Offset: 0x2C

Bit

Name

Description

Attribute

Reset

31:2

Reserved

NDT5V_DET

Power noise status of NDT5V IP.
0: No power noise is detected.
1: Power noise is detected by NDT5V IP.

*Cleared by write 1 to SYS0_NDTSTS[1]

R/W

Reserved

3.3.13 Anti-EFT Ability Control register (SYS0_ANTIEFT)

Address Offset: 0x30

This register decides the HW anti-EFT ability.

Bit

Name

Description

Attribute

Reset

31:3

Reserved

2:0

AEFT[2:0]

HW anti-EFT ability.

000: No
010: Low
011: Medium
100: Strong

R/W

000

3.3.14 IHRC Frequency Adjustment register (SYS0_IHRCADJ)

Address Offset: 0x34

Total 400 counts available for IHRC frequency adjusting, and each step varies b/-0.2% from +/-0.3%.

Bit

Name

Description

Attribute

Reset

31:16

SYSKEY[15:0]

System register key
Read as 0. Behavior of writing to this register is ignored unless writing
0xA5A5 to SYSKEY at the same time.

15:12

Reserved

11:4

ADJ[7:0]

IHRC frequency adjusting bits.

R/W

3:2

Reserved

DIR

IHRC frequency adjusting direction bit
0: Positive
1: Negative

R/W

ADJEN

IHRC frequency adjustment enable bit
0: Disable
1: Enable

R/W

Summary of Contents for SN32F280 Series













































































































































































































































































Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands

SONIX SN32F280 Series, User Manual

Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands