SONIX SN32F260 Series Page 92 User Manual Download

Page: 92 / 141

SN32F260 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 92

Version 1.5

8.6 SPI REGISTERS

Base Address: 0x4001 C000 (SPI0)

8.6.1 SPI n Control register 0 (SPIn_CTRL0) (n=0)

Address Offset:0x00



Note:



1. Must reset SPI FSM with FRESET[1:0] after changing any configuration of SPI when SSPEN = 1.



HW will switch I/O configurations refer to FORMAT bit directly when

SSPEN = 1.

Bit

Name

Description

Attribute

Reset

31:19

Reserved

SELDIS

Auto-SEL disable bit. For SPI mode only.
0: Enable Auto-SEL flow control.
1: Disable Auto-SEL flow control.

R/W

17:15

RXFIFOTH[2:0]

RX FIFO Threshold level
000: RX FIFO threshold level = 0.
001: RX FIFO threshold level = 1.
…
…
111: RX FIFO threshold level = 7.

R/W

000b

14:12

TXFIFOTH[2:0]

TX FIFO Threshold level
000: TX FIFO threshold level = 0.
001: TX FIFO threshold level = 1.
…
…
111: TX FIFO threshold level = 7.

R/W

000b

11:8

DL[3:0]

Data length = DL[3:0] + 1.
0000~0001: Reversed.
0010: data length = 3.
…
…
1110: data length = 15.
1111: data length = 16.

R/W

1111b

7:6

FRESET[1:0]

SPI FSM and FIFO Reset bit.
00: No effect.
01: Reserved.
10: Reserved.
11: Reset finite state machine and FIFO. (BUF_BUSY = 0, data in shift

BUF is cleared, TX_EMPTY = 1, TX_FULL = 0, RX_EMPTY = 1,
RX_FULL = 0, and data in FIFO is cleared). This bit will be cleared by
HW automatically.

Reserved

FORMAT

Interface format.
0: SPI.
1: Reserved.

R/W

Master/Slave selection bit.
0: Act as Master.
1: Act as Slave.

R/W

SDODIS

Slave data output disable bit. (ONLY used in slave mode)
0: Enable slave data output.
1: Disable slave data output. (MISO=0)

R/W

LOOPBACK

Loop back mode enable.
0: Disable.
1: Data input from data output.

R/W

SSPEN

SPI enable bit.
0: Disable.

R/W

Summary of Contents for SN32F260 Series














































































































































Search results

Summary of Contents for SN32F260 Series

Reviews:

Related manuals for SN32F260 Series

Brands by name

Popular brands

SONIX SN32F260 Series, User Manual

Search results

Summary of Contents for SN32F260 Series

Reviews:

Related manuals for SN32F260 Series

Brands by name

Popular brands