SONIX SN32F107 User Manual Download | Manualshive

Page: 70 / 184

background image

SN32F100 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 70

Version 1.9

00: Pull-up resistor enabled.
01: Pull-down resistor enabled.
10: Inactive (no pull-down/pull-up resistor enabled).
11: Repeater mode.



Note: HW will switch P1.7 and P1.8 to Microphone differential input if SEL_MIC=1 in ADC_SET23 register.
Setting SEL_MIC=0 before P1.7 and P1.8 as GPIO function.



Note: P0.14 is the input pin only, please don

’t set it to the output function in GPIO0_MODE register.

5.3.4 GPIO Port n Interrupt Sense register (GPIOn_IS) (n=0,1,2,3)

Address offset: 0x0C

Bit

Name

Description

Attribute

Reset

31:16

Reserved

R

0

15:0

IS[15:0]

Selects interrupt on pin x as level or edge sensitive (x = 0 to 15).
0: Interrupt on Pn.x is configured as edge sensitive.
1: Interrupt on Pn.x is configured as event sensitive.

R/W

0

5.3.5 GPIO Port n Interrupt Both-edge Sense register (GPIOn_IBS) (n=0,1,2,3)

Address offset: 0x10

Bit

Name

Description

Attribute

Reset

31:16

Reserved

R

0

15:0

IBS[15:0]

Selects interrupt on Pn.x to be triggered on both edges (x = 0 to 15).
0: Interrupt on Pn.x is controlled through register GPIOn_IEV.
1: Both edges on Pn.x trigger an interrupt.

R/W

0

5.3.6 GPIO Port n Interrupt Event register (GPIOn_IEV) (n=0,1,2,3)

Address offset: 0x14

Bit

Name

Description

Attribute

Reset

31:16

Reserved

R

0

15:0

IEV[15:0]

Selects interrupt on pin x to be triggered rising or falling edges (x = 0 to 15).
0: Depending on setting in register GPIOn_IS, Rising edges or HIGH level

on Pn.x trigger an interrupt.

1: Depending on setting in register GPIOn_IS, Falling edges or LOW level

on Pn.x trigger an interrupt.

R/W

0

5.3.7 GPIO Port n Interrupt Enable register (GPIOn_IE) (n=0,1,2,3)

Address offset: 0x18

Bits set to HIGH in the GPIOn_IE register allow the corresponding pins to trigger their individual interrupts. Clearing a
bit disables interrupt triggering on that pin.

Bit

Name

Description

Attribute

Reset

31:16

Reserved

R

0

15:0

IE[15:0]

Selects interrupt on pin x to be enabled (x = 0 to 15).
0: Disable Interrupt on Pn.x
1: Enable Interrupt on Pn.x

R/W

0

«
...
68
69
70
71
72
...
»

Summary of Contents for SN32F107

























































































































































































Reviews:

No comments

Related manuals for SN32F107

Brand: Abicor Binzel Pages: 8

Brand: Gardena Pages: 17

Brand: Badger Meter Pages: 16

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

DIGITAL EPIC-2 DTM

Brand: Westlock Pages: 33

Brand: Qorvo Pages: 6

Brand: Current Pages: 4

Brand: PEAS Pages: 4

Brand: Sollae Systems Pages: 72

Brand: Mita Pages: 7

Brand: VDH Pages: 4

Brand: VIRDI Pages: 73

Sigma II Series

Brand: YASKAWA Pages: 359

Brand: Hamamatsu Pages: 50

Brand: Hanbay Pages: 13

SetPro MV Series

Brand: Gigarise Pages: 18

Brand: X10 Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands