manualshive.com logo in svg

Sonifex CM-CU1, Handbook

Share
Download
Sonifex CM-CU1 Handbook Download Page 34

24

2       CM-CU21 Configuration Options

Commentator 2 TALKBACK A button: 
Mode 1  Commentator 2 TALKBACK A button momentary mode enabled 
 (default). 
Mode 2  Commentator 2 TALKBACK A button latching mode enabled. 
Mode 3  Commentator 2 TALKBACK A button momentary and latching 
 

modes enabled.

Commentator 2 TALKBACK B button: 
Mode 1  Commentator 2 TALKBACK B button momentary mode enabled 
 (default). 
Mode 2  Commentator 2 TALKBACK B button latching mode enabled. 
Mode 3  Commentator 2 TALKBACK B button momentary and latching 
 

modes enabled.

Commentator 3 ON AIR button: 
Mode 1  Commentator 3 ON AIR is permanently disabled and cannot be 
 selected. 
Mode 2  Commentator 3 ON AIR can be selected as normal (default). 
Mode 3  Commentator 3 ON AIR is permanently selected and cannot be 
 disabled.

Please note:

 Momentary mode button operation – press to activate, 

release to deactivate. Latching mode button operation – press once to 
activate, press again to deactivate.

Config Page 2 - Line Input Routing to Output

Commentator 1 ON AIR button: 
Mode 1  Commentator 3 line mode input is routed to Commentator 1 
 

headphones (default). 

Mode 2  Commentator 3 line mode input is not routed to Commentator 1 
 headphones.

Commentator 1 TALKBACK A button: 
No associated option on this page.

Commentator 1 TALKBACK B button: 
No associated option on this page.

Commentator 2 ON AIR button: 
Mode 1  Commentator 3 line mode input is routed to Commentator 2 
 

headphones (default). 

Mode 2  Commentator 3 line mode input is not routed to Commentator 2 
 headphones.

Commentator 2 TALKBACK A button: 
No associated option on this page.

Commentator 2 TALKBACK B button: 
No associated option on this page.

Commentator 3 ON AIR button: 
No associated option on this page.

Config Page 3 - Commentator Mic & Line Input Routing to 
Headphones

Commentator 1 ON AIR button: 
Mode 1  Commentator 1 input permanently routed to Commentator 1 
 headphones. 
Mode 2  Commentator 1 input routed to Commentator 1 headphones only 
 

when Commentator 1 ON AIR is active (default).

Commentator 1 TALKBACK A button: 
Mode 1  Commentator 2 input permanently routed to Commentator 1 
 headphones. 
Mode 2  Commentator 2 input routed to Commentator 1 headphones only 
 

when Commentator 2 ON AIR is active (default).

Commentator 1 TALKBACK B button: 
Mode 1  Commentator 3 input permanently routed to Commentator 1 
 headphones. 

Summary of Contents for CM-CU1













































Reviews:

No comments

Brands by name

Popular brands

Load more brands