manualshive.com logo in svg

SOMFY Animeo 1870452, Manual

Share
Download
SOMFY Animeo 1870452 Manual Download Page 35

 

animeo KNX 4 DC Motor Controller 

28.02.2019 

 

WM 24 V DC 

 
 

 2019 Somfy Activités SA 

 Ref. 5147817A 

35/56 

6.7.4  Contact type input B 

Default value: 

  0 

Selection options: 

  0 

– 255 

 
With this parameter the value is set which is transmitted with a rising edge at the local input B. 
 

6.7.5  Contact B value on rising edge (0-255) 

Default value: 

  Normally open 

Selection options: 

  Normally open 

 

  Normally closed 

 
With this parameter it is defined which contact type is at the local input B. 
Normally open: The contact at the local input is activated closed and not activated opened. 
Normally closed: The contact at the local input is activated opened and not activated closed. 
 
 

6.8 

Menu index card “Binary inputs – Dimming” 

 

 

 

6.8.1  Basic Function 

Selected option: 

  Dimming 

 

6.8.2  Long operation (dimming) after 

 
Default value: 

  0.5 seconds 

Selection options: 

  0.3 - 5.0 seconds 

 
This parameter defines the activity time of the corresponding push button which makes a distinction between 
the sending of a switching telegram and a dimming telegram. If the time, for example, is parameterized on 
0.5 seconds, a dimming telegram is generated only after a press longer than 0.5 seconds is made. With a 
pressing shorter than 0.5 seconds a switch telegram is generated. 
 

6.8.3  Input A/B 

Default value: 

  On/Off 

Selection options: 

  On/Off  

 

  Toggle/Toggle 

 
This parameter defines the value which is transmitted with a short pressing of the corresponding input. 

 

Summary of Contents for Animeo 1870452

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands