SOMFY Animeo 1870452 Manual Download Page 28

Page: 28 / 56

animeo KNX 4 DC Motor Controller

28.02.2019

WM 24 V DC



2019 Somfy Activités SA



Ref. 5147817A

28/56

value (0%)

value (100%)

6.3 Menu index card

“Functions for motor 1...4”

Four single menu index cards (Functions motor

1…4) become visible if on the menu card index “General”,

the basic setting of the blinds on

“Individual” is parameterized. A menu index card (Motor 1 - 4) becomes visi-

ble if on the menu card index

“General”, the basic setting of the motors is parameterized to “Combined”.

6.3.1 Intermediate Position 1 (IP1)

6.3.1.1 Up/Down position (0-100%)

Default value:



0 % (function disabled)

Selection options:



0 - 100 %

With this parameter the intermediate position 1

“UP/DOWN” is defined. The set value in % refers to the

parameterized move times of the corresponding blind of the menu index card Motor

1…4/Motor 1 - 4.

If the IP UP/Down position parameter is set to 0 %, the IP position is disabled. This function avoids any
movement of the blinds by using the “my” or IP push button.

6.3.1.2 Slat position (0-100%)

Default value:



0 %

Selection options:



0 - 100 %

With this parameter the intermediate position 1

“slats” is defined. The set value in % refers to the parameter-

ized complete slats turn of the corresponding blind of the menu index card Motor

1…4/Motor 1 - 4.

Intermediate position 1 can be learned-in individually via conventional local push buttons or by a radio

handheld transmitter per motor output. In addition, the last learned-in position applies.

Summary of Contents for Animeo 1870452
























































Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands

SOMFY Animeo 1870452, Manual

Search results

Summary of Contents for Animeo 1870452

Reviews:

Brands by name

Popular brands