manualshive.com logo in svg

Soma Networks SOMAport R3.0, Setup Manual

Share
Download
Soma Networks SOMAport R3.0 Setup Manual Download Page 22

22

C

ONNECT

 M

ULTIPLE

 C

OMPUTERS

 

TO

 

THE

 

SOMA

PORT

You can connect the SOMAport to an Ethernet hub, switch, or router 
device (referred to in the rest of this section as “hub” generically) in 
order to share the Internet connection among many computers. 

The SOMAport functions as a DHCP server (it automatically assigns IP 
addresses to devices attached to it). Consult the documentation for your 
hub for information about how to configure the hub and computers for 
Internet access via the SOMAport.

 

To connect an Ethernet hub to the SOMAport

1

Insert one end of the straight-through Ethernet cable into the Ethernet port 
on the SOMAport. 

2

Insert the other end of the cable into an uplink port (sometimes labeled as a 
WAN or Internet port) on the hub. 

NOTE: 

If the Ethernet hub does not have an uplink port, you may connect to 

the SOMAport using an Ethernet port (which may be labeled as a switched, 
LAN, or numbered port) on the hub. However, you must obtain and use a 
crossover Ethernet cable (not shipped with the SOMAport) to make this 
connection.

3

Configure the hub and computers as required to access the Internet via the 
SOMAport.

sp3.book  Page 22  Thursday, July 22, 2004  3:21 PM

Summary of Contents for SOMAport R3.0



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands