manualshive.com logo in svg

SOLTEK 65kv, User Manual, Page: 41 / 48

Share
Download
SOLTEK 65kv User Manual Download Page 41

65KV

41

Enabled (default): Turn on the onboard IDE function.
Disabled: Turn off the onboard IDE function.

On-Chip Primary/

Choose Enabled (default) or Disabled. Choose Disabled
when you use an ISA card with FDD function, or choose
Enabled to use the onboard FDD connector.

Onboard FDC

Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3 or Disabled. Don’t set port 1 & 2 to the same
value, except when setting at Disabled.

Onboard Serial Port1

Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3 or Disabled.

Onboard Serial Port2

Choose Standard (default), HPSIR or ASKIR.

UART 2 Mode

Choose Half or Full.

IR Function Duplex

Choose the printer I/O address: 378H/IRQ7 (default),
3BCH/IRQ7, 278H/IRQ5 or Disabled.

Onboard Paralle Port

Choose Normal (default), ECP/EPP, SPP mode. The
mode depends on the external device connected to this
port.

Onboard Parallel Mode

Choose Auto (default) or Mode 0~4. The BIOS will detect
the HDD mode type automatically when you choose Auto.
You need to set to a lower mode than Auto when your hard
disk becomes unstable.

IDE Primary

Master/Slave PIO

IDE Secondary

Note: This option will not be displayed unless the EPP/ECP

Choose DMA3 (default) or DMA1. Most sound cards use
DMA1. Check with your sound card configuration to make
sure that there is no conflict with this function.

ECP Mode Use DMA

Summary of Contents for 65kv

















































Reviews:

No comments