Quick Installation Guide
ASW6000-S / ASW8000-S/ASW10000-S
1. The contents of this document may be updated due to product upgrades or other reasons. Unless
otherwise specified, this document only works as guide. All statements, information and
suggestions in this document do not constitute any guarantee.
2. This product can only be installed, commissioned, operated and maintained by technicians who
have carefully read and fully understood the user manual.
3. This product must only be connected with PV modules of protection class II (in accordance with
IEC 61730, application class A). PV modules with a high capacitance to ground must only be used
if their capacity does not exceed 1μF.
Do not connect any sources of energy other than PV
modules to the product.
4. When exposed to sunlight, the PV modules generate dangerous high DC voltages which is present
in the DC cable conductors and live components. Touching live DC cable conductors and live
components can result in lethal injuries due to electric shock.
5. All components must remain within their permitted operating ranges at all times.
6. The product complies with Electromagnetic compatibility 2014/30/EU, Low Voltage Directive
2014/35/EU and Radio Equipment Directive 2014/53/EU.
1. Ensure that the inverter is installed out of the reach of children.
2. To ensure best operating status and prolonged service life, the
ambient temperature of the location should be
≤
40
°
C.
3. To avoid direct sunlight, rain, snow, pooling of water on the inverter, it is
suggested to mount the inverter in places which are shaded during the majority of
the day or to install an external cover that provides shade for the inverter.
Do not place a cover directly on top of the inverter.
4. The mounting condition must be suitable for the weight and size of the inverter. The inverter is suitable
to be mounted on a solid wall that is vertical or tilted backwards
(Max. 15°). It is not recommended to
install the inverter on walls made of plasterboards or similar materials. The inverter may emit noise
during operation.
5. To ensure adequate heat dissipation, the recommended clearances between the
inverter and other objects are shown in the image to the right:
1.
Use a Φ1
0mm bit to drill 2 holes at a depth of about 70mm according to the location of the wall
mounting bracket. (Figure A)
2. Insert the wall plugs into the wall and fix the mounting bracket to the wall by inserting two Screws
(SW10). (Figure B)
3.
Push the inverter to wall bracket and hook it. Ensure the two right- and left-hand keys on the outer ribs
of the inverter must be hooked into the respective keyways in the wall mounting bracket. (Figure C)
4. Ensure that the inverter is securely in place, then secure the inverter to the mounting bracket on both
sides using two M5 screws. Screwdrivertype:PH2, torque:2.5Nm. (Figure D)
1. Strip the AC cable as shown in the figure
，
and crimp the copper wire to the appropriate cord end
terminal (according to DIN 46228-4, provided by the customer).
Object
Description
Value
A
External diameter
14-20mm
B
Copper conductor cross-section
6-16mm
2
C
Stripping length of the insulated conductors
16mm
D
Stripping length of the cable outer sheath
46mm
Note: the PE conductor is at least 5mm longer than the L and N conductors.
2. Insert the PE, N and L conductor into the cord end terminal, insert them into the corresponding
terminals of the AC connector in the order as shown, and tighten the screws by the hex key with a
suggested torque of 2.0 Nm.
3.
Secure the connector body assemble to the connector, then tighten the nut cap to the connector
body.
4. Insert the AC connector plug into the output socket of AC connector corresponding to the inverter and
tighten them.
5. If required, you can connect a second protective conductor as equipotential bonding.
6. if required
，
you can use a slot type screwdriver to disassemble the AC connector plug from the inverter.
Object
Description
M5 screw
Screwdriver type: PH2, torque: 2.5Nm
OT terminal lug
Customer provided, type: M5
Grounding cable
Copper conductor cross-section: 6-16mm
2
2
Figure A
Figure B
I. Safety Instruction
II. Mounting environment
IV. Inverter's mounting
Figure C
Figure D
V. AC connection
▪
All electrical installations must be done in accordance with all local and national rules.
▪
Ensure that all DC switches and AC circuit breakers have been disconnected and all power sources
have been electrically isolated before any electrical terminations have been made. High voltages
produced by the inverter may lead to electrical shock.
▪
In accordance with safety regulations, the inverter needs be correctly grounded. When a poor
ground connection (PE) occurs, the inverter will report PE grounding error. Please check and ensure
that the inverter is grounded firmly or contact AISWEI service.
3
1
III. Scope of delivery