Solid RocketWAVE SRF-L-8A1821 Product Manual Download Page 21

Page: 21 / 25

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual

V1.7 - DEC 2021

Page 21

the AMP is ON. If the button is

, the AMP is off.

⑦

Displays each band

’s Uplink signal information such as the in/output signal strength and current Gain

values. Also the AMP of each band can be on and off using the button. If the button is

, the

AMP is ON. If the button is

, the AMP is off.

⑧

If a band is unused (not in service), turn off the band using the deactivation button (Click

button

to deactivate. To activate, click

). Once the band is deactivated, entire corresponding compo-

nents on GUI are disabled and appears in grey colour.

⑨

Provides the AMP

’s OFF reason and AGC controllable panel. When the AMP is off by the user, it

shows

‘User Control’ for its reason. For the AGC function, AGC mode changing button, its level control-

ler, and function on and off are available. To turn on the AGC, click

. Then the button changes

⑩

Provides the Isolation controllable panel. Click

to perform Isolation Recheck. When the re-

peater measures the isolation value, it appears

‘Isolation Value’, and the gain value is automatically

tuned.

To upgrade to the latest firmware, follow the steps as described below:

①

Prepare a firmware file (*.RSM).

②

Press [F7] to open the firmware upgrade popup. When the popup appears, click [Open].

③

Select the firmware file.

④

Click [Start] to start upgrade.

⑤

When the upgrade completes, you will be asked the system reset. Click [OK].

⑥

When the system is back, check the firmware version upgraded correctly.

Summary of Contents for RocketWAVE SRF-L-8A1821























Search results

Summary of Contents for RocketWAVE SRF-L-8A1821

Reviews:

Related manuals for RocketWAVE SRF-L-8A1821

Brands by name

Popular brands

Solid RocketWAVE SRF-L-8A1821, Product Manual

Search results

Summary of Contents for RocketWAVE SRF-L-8A1821

Reviews:

Related manuals for RocketWAVE SRF-L-8A1821

Brands by name

Popular brands