Solid State Logic Sigma User Manual Download Page 35

Page: 35 / 72

rebooT button

When you make a change in the

SeTTINGS

page that requires Sigma to be restarted in order for the change to have effect,

a message will prompt you to perform a restart. The

SoFTwAre UPDATe

button will temporarily change to a

rebooT

button. Click this to restart Sigma.

SAve

AND

LoAD b

UTToNS

The

SAve

button will save all of Sigma’s settings across the three main pages -

mAIN

CHANNeLS

and

SeTTINGS

Upon clicking the

SAve

button you will be presented with a pop-up asking you to name

the file and choose a destination on your computer/network.

The

LoAD

button enables you to recall a previously saved Sigma setup.

Upon clicking the

LoAD

button you will be prompted to locate a saved Sigma file from your computer/network.

Sigma files are saved as .xml type files.

Page 35

Summary of Contents for Sigma









































































Search results

Summary of Contents for Sigma

Reviews:

Related manuals for Sigma

Brands by name

Popular brands

Solid State Logic Sigma, User Manual

Search results

Summary of Contents for Sigma

Reviews:

Related manuals for Sigma

Brands by name

Popular brands