Solid State Logic Sigma User Manual Download Page 31

Page: 31 / 72

Page 31

SeTTINGS

Unlike the

mASTer

and

CHANNeLS

pages of Sigma, the

SeTTINGS

page does not mirror any section of the front panel.

This page contains many important setup aspects of Sigma.

SeTUP box

NAme

This box allows you to name your Sigma unit. This will be useful when using more than one Sigma.

DAw/ProToCoL SeLeCTIoN

This must be set in order to allow Sigma to correctly translate automation data from the DAW. There are five options:

• Pro Tools (HUI)
• Logic (mCU)
• Cubase/Nuendo (mCU)
• Ableton (mCU)
• mIDI

See Chapter 6 ‘

Example Setups

’ for more information on which one to choose for your setup.

ipmIDI Ports

CHANNeLS 1-8

Select the ipMIDI Port number to match your first HUI/MCU unit in your DAW.

CHANNeLS 9-16

Select the ipMIDI Port number to match your second HUI/MCU unit in your DAW.

Summary of Contents for Sigma









































































Search results

Summary of Contents for Sigma

Reviews:

Related manuals for Sigma

Brands by name

Popular brands

Solid State Logic Sigma, User Manual

Search results

Summary of Contents for Sigma

Reviews:

Related manuals for Sigma

Brands by name

Popular brands